User manual PANASONIC KX-TC1486B

[. . . ] 900 MHz Cordless Phone Operating Instructions Model No. KX-TC1486 Pulse-or-tone dialing capability The unit is Caller ID compatible. To display the caller's name and phone number, you must subscribe to Caller ID service. PLEASE READ BEFORE USE AND SAVE. Charge the battery for 15 hours before initial use. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Before Initial Use Thank you for purchasing your new Panasonic cordless telephone. Read and understand all instructions. Caller ID and Call Waiting Service, where available, are telephone company services. [. . . ] These codes help prevent the unauthorized use of your telephone line by another cordless telephone user. Advanced Operation Handset Locator You can locate the handset or page the handset user with beep tones from the base unit. 1 2 Press [HANDSET LOCATOR]. The IN USE/CHARGE indicator flashes. The handset beeps for 1 minute and "PAGING" is displayed on the handset. To stop paging, press [HANDSET LOCATOR] again or press [OFF] on the handset. Temporary Tone Dialing (For Rotary or Pulse Service Users) Press [ ] (TONE) before entering access numbers which require tone dialing. The dialing mode changes to tone. You can enter numbers to access an answering service, electronic banking service, etc. For assistance, please call: 1-800-211-PANA(7262) 25 " Special Features Using the PAUSE Button (For PBX Line/Long Distance Calls) We recommend you press [PAUSE/REDIAL] if a pause is required for dialing with a PBX or to make a long distance call. Ex. Line access number [9] (PBX) [9] ¤ [PAUSE/REDIAL] ¤ Phone number Pressing [PAUSE/REDIAL] once creates a 3 second pause. Pressing [PAUSE/REDIAL] more than once increases the length of the pause between numbers. For Call Waiting Service Users Press [ /FLASH] if you hear a call-waiting tone during a conversation. The first call is put on hold and you can answer the second call. The call waiting service cannot be used when a parallel connected telephone is in use. If this function does not operate properly, consult your telephone company for details. Call Waiting Caller ID display If you subscribe to both Caller ID and Call Waiting with Caller ID services (CWID), when a second call is received while talking, the second caller's information will be displayed. After you hear a call-waiting tone while talking, the unit will display the caller's name, the phone number and the date and time received. BROWN, NANCY Please contact your telephone company for details and availability in your area. 26 Belt Clip You can hang the handset on your belt or pocket using the belt clip. To attach the belt clip To remove the belt clip Optional Headset Plugging an optional headset into the handset allows a hands-free phone conversation. To order, call the accessories telephone number on page 2. Connecting an optional headset to the handset Open the headset jack cover, and connect an optional headset to the headset jack as shown below. Useful Information The illustration of the headset is KX-TCA86. Headset Jack When an optional headset is connected to the handset, make sure to use the headset to talk with the caller. If you want to have a normal cordless phone conversation, disconnect the headset. For assistance, please call: 1-800-211-PANA(7262) 27 Wall Mounting This unit can be mounted on a wall phone plate. 1 Push the lower side of the hook (1) and pull down the hook until it locks (2), so the tab holds the handset. 2 1 2 3 Remove the wall mounting adaptor. 2 1 Connect the AC adaptor. Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow (1 and 2). The word "UP WALL" should face upward. Fasten the AC adaptor cord to prevent it from being disconnected. Hook 2 To Power Outlet 1 4 Connect the telephone line cord. Mount the unit, then slide down. Raise the antenna. Wall Phone Plate 28 5 To charge the battery: Fit the handset hole in the tab (1) and fix the charge contacts (2). Make sure to place the handset with the keypad facing down. 1 Hole Tab 2 Adding Another Phone This unit will not work during a power failure. To connect a standard telephone on the same line, use the Panasonic KX-J66 T-adaptor. To order, call the accessories telephone number on page 2. Standard Telephone Useful Information Telephone Line Cord Single-Line Telephone Jack T-Adaptor (KX-J66) For assistance, please call: 1-800-211-PANA(7262) 29 Battery Replacement If "RECHARGE" and " " are displayed after a few telephone calls even if the battery was fully charged, replace the battery with a new Panasonic PQWBTC1461M (P-P504) battery. To order, call the accessories telephone number on page 2. 1 Press the notch on the handset cover firmly (1) and slide it as indicated by the arrow (2). 1 2 2 Remove the old battery. Then install the new one. Insert the battery plug into the connector as shown in the picture. Be sure wires are free from being pressed by the battery body or handset cover. [. . . ] Parts Labor One (1) Year One (1) Year During the "Labor" Limited Warranty period there will be no charge for labor. During the "Parts" Limited Warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for batteries, antennas, and cosmetic parts (cabinet). This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. [. . . ]