User manual PANASONIC KX-TCD200FX

[. . . ] TCD200FX(e-e). book Page 1 Monday, February 7, 2005 1:19 PM Operating Instructions Digital Cordless Phone Model No. KX-TCD200FX This unit is Caller ID compatible. To display the caller's phone number, you must subscribe to Caller ID service. Charge the batteries for about 7 hours before initial use. Please read these operating instructions before using the unit and save them for future reference. TCD200FX(e-e). book Page 2 Monday, February 7, 2005 1:19 PM Introduction Introduction Thank you for purchasing a new Panasonic digital cordless phone. For your future reference Attach or keep original receipt to assist with any repair under warranty. [. . . ] 6 Enter the desired hour and minute you wish to start this feature by selecting 2 digits for each. L If you use 12-hour time entry, select "AM" or "PM" by pressing {*} repeatedly before entering the time. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 6 Select the desired setting, then press {>}. 7 Enter the desired hour and minute you wish to end this feature by selecting 2 digits for each. 7 Press {ih}. 19 TCD200FX(e-e). book Page 20 Monday, February 7, 2005 1:19 PM Handset Settings Selecting categories to bypass night mode 4 Select "Standby Display", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 5 Select the desired setting, then press {>}. 6 Press {ih}. Note: L If "Base Number" is selected and the current base unit number is 2, "-2-" is displayed. L If "Handset Number" is selected and the current handset number is 2, "[2]" is displayed. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Select Category", then press {>}. 6 Press the desired category numbers, then press {j/OK}. The number will stop flashing. Changing the display language 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 7 Press {ih}. Note: L If a call is received from one of the categories set to bypass night mode, only the handset will ring. 3 Select "Display Setup", then press {>}. 4 Select "Select Language", then press {>}. 5 Select the desired language, then press {>}. 6 Press {ih}. Display setup Selecting the standby mode display "Base Number": The current base unit number is displayed. "Off": Only the current date and time are displayed. Note: L If you select a language you cannot read, press {ih}, {j/OK}, press {e} 2 times, press {>}, press {v} 2 times, press {>}, press {v}, press {>}, select the desired language, then press {>}. 2 Select "Handset Setup", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Display Setup", then press {>}. 3 Select "Display Setup", then press {>}. 4 Select "Contrast", then press {>}. 20 TCD200FX(e-e). book Page 21 Monday, February 7, 2005 1:19 PM Handset Settings 5 Press {e} or {v} repeatedly to select the desired contrast, then press {>}. 6 Press {ih}. Other options Changing the handset PIN (Personal Identification Number) For security, the handset PIN must be entered when changing certain settings. If you forget your PIN, consult your nearest Panasonic service centre. Call options Turning call bar on/off This feature prohibits making outside calls. When call bar is turned on, only intercom calls and calls to emergency numbers (page 25) can be made. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Call Options", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 4 Select "Call Bar", then press {>}. 5 Enter "0000" (default handset PIN). L If you changed the PIN, enter it (page 21). 3 Select "Other Options", then press {>}. 4 Select "Handset PIN", then press {>}. 6 Select "On" or "Off", then press {>}. 7 Press {ih}. Note: L When call bar is turned on, o is displayed. 5 Enter the current 4-digit handset PIN. 6 Enter the new 4-digit handset PIN, then press {j/OK}. 7 Press {ih}. Turning keytones on/off Keytones are tones heard when keys are pressed. Includes confirmation tones and error tones. Turning auto talk on/off When this feature is turned on, you can answer calls simply by lifting the handset off the base unit. 2 Select "Handset Setup", then press {>}. 1 Press {j/OK}. [. . . ] If the working telephone does not operate properly, contact your service provider. Adjust the handset ringer volume (page 18) and the base unit ringer volume (page 24). L Locate the handset and the base unit away from other electrical appliances. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack. The unit does not ring. The batteries should be charging but the battery icon does not change. [. . . ]