User manual PANASONIC KX-TCD650

[. . . ] Model No: KX-TCD650E Digital Cordless Phone Operating Instructions & Quick Guide Centre Page Pullout Safety Information . . 9 . 10 . 13 . 16 . 17 . 20 . 22 Caller ID compatible Please read before use and save Charge the batteries for approx. 15 hours before initial use General Safety Only use the power supply included with the product. Do not connect the AC Adaptor to any AC outlet other than the standard AC220-240V. [. . . ] ZV. call waiting (Set Call Waiting Tone ON/OFF)* To program see * below. Call waiting tone sounds when an incoming external call is received during an intercom call. call opt (Call Options): ZV. ZS or U. range alarm (Set Range Alarm ON/OFF)* To program see * below. Alarm will sound when you move out of range of a base unit. call bar (Set Call Prohibition ON/OFF): This allows you to make emergency and intercom calls only. If on is selected, Ô is displayed. battery low (Set Battery Low Tone ON/OFF)* * Program as follows ZV. ZS or U. (Enter a Direct Call Number): After a Direct Call phone number has been entered and Direct Call set to ON, you can call the Direct Call number only, by pressing . ZS or U to select from bs no (Base Unit number), hs no (Handset Number), clock (Clock) or off (Off). 08700 100 076 11 Handset Settings Before programming, please follow steps 1 to 4 of `Handset Settings'. set direct battery type (Set Direct Call ON/OFF): ZV. If ON is selected, Ë is displayed. (Set Battery Type Ni-MH / Ni-Cd): Select the type of battery installed. If the battery type selected is not the same as the type of battery installed, the battery level icons will not be correct. ZS or U. hspin change (Change Handset PIN): You can change the 4 digit password for the handset. (If the PIN is entered incorrectly, an error tone sounds and display returns to new pin ____. If you forget it, please consult our Panasonic Customer Care Helpline. 01289 8333 register hs (Registering a Handset to a Base Unit)* cancel base (Cancelling a Base Unit)* select bs (Select Base Unit)* *For information on registering handset(s), cancelling and selecting base unit(s), please refer to `For Optional Multi-Unit Users'. Handset Settings reset hs (Reset the Handset Settings): You can reset all of the handset settings to their initial factory settings (see `Handset Initial Settings'). cleared is displayed and display returns to settings menu. auto talk (Set Auto Talk ON/OFF): If you set Auto Talk to ON, you can answer the phone by lifting the handset off the base unit. 01289 8333 Base Unit Settings You can change the base unit settings using a handset near the base unit. Before proceeding with any of the base settings listed in this chapter, the following procedure must initially be carried out: 1 2 3 From the standby mode, ZV. Please note: Where `Enter PIN' is stated in this chapter, it refers to the 4 digit Base Unit PIN. To exit the menu at any time, Z±. Ringer Mode To select all handsets to ring ZA. ZV. Selecting Time Break Recall (TBR) / Earth Recall Mode (option) The factory setting is time break recall (TBR). If your PBX requires earth recall mode, this can be added at an extra cost. ZB then B for earth mode OR ZB then A for time break recall mode (TBR). [. . . ] 01289 8333 Problem Possible cause Solution Cannot register handset to base. · Max. · Electrical noise in local area. · Delete unused base registrations from handset. · If PIN number is lost, contact the Panasonic Customer Care Helpline. · Move base / handset away from sources of electrical noise ( e. g TV, radio ). If you still have a problem please contact our Customer Care Helpline (Monday - Friday 9:00am - 5:30pm) on : U. K. [. . . ]