User manual PANASONIC NN-CT552W

[. . . ] 4 PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 HOW TO ASSEMBLE YOUR VACUUM CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 A) Handle Assembly / Hose Assembly / Mains Lead Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 * * * * * * B) Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ■ Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. ■ Do not use to pick up flammable or combustible materials, or other that may become so or use in areas where they may be present. ■ This appliance should be serviced by an authorised Panasonic Service Centre, and only genuine Panasonic spare parts should be used. Always keep the back side of the vacuum cleaner touch to the stair to prevent the cleaner from falling. ■ Keep bare feet and hands away from the beater bar (It may cause injury). NOTE: This vacuum cleaner is designed for general domestic use only and is not suitable for use in a garage, garden or to suck up liquids. CAUTIONS: Obey the following instructions in order to avoid any injury or physical damage to property. 1. To avoid any possible damage to the mains lead, never run over the mains lead or allow it to become caught in the beater bar when using the vacuum cleaner. 2. Do not run the vacuum cleaner over tassels or fringes of rugs or mats as they could get caught up in the beater bar and may cause damage to the brush and belt. 3. Keep the vacuum cleaner away from heat sources such as radiators, fire, direct sunlight, etc. 4. To avoid damaging the machine, never let the vacuum cleaner pick up wet matter, mud, burning ashes or large and sharp objects. 5. Do not pull on the mains lead when disconnecting the appliance from the socket outlet, always pull on the plug body itself. 6. • This bracket may release in order to prevent damage to the dust bin or the dust bin plate due to the dust bin was dropped or the dust bin plate getting any impact. Lid Holding Bracket Hinge • To reassemble, put the hinge of the dust bin plate to its original location as shown. • Slide the lid holding bracket to its original location as shown and push until you hear a “click” sound. NOTE: • Push the lid holding bracket using both palm if the lid holding bracket is difficult to push in. 11 MAINTAINING THE HEPA FILTER UNIT Lid Pull to release Pull to release • Check HEPA filter unit frequently and clean when dirty. • Remove HEPA filter unit from dust bin by pulling both buckle as shown. • Clean HEPA filter unit by gently tapping over a rubbish container. • Reinstall the HEPA filter unit as per reverse procedure. HEPA Filter Unit Buckle Dust Bin TO CLEAN THE PRE-FILTER • Remove HEPA filter unit from dust bin. • Grasp the pre-filter and turn it clockwise and pull the pre-filter out as shown. Clean by gently tapping over a rubbish container. Pre-Filter • Install the pre-filter to the dust bin, aligning the pre-filter tabs to the dust bin slots. Each Pre Filter Tabs is different shape and adjust it to match Dust Bin Slot, then turn counter-clockwise to the lock position until you hear a “click” sound as shown. Dust Bin Slot • After the dust bin is empty, firmly close the dust bin plate. Make sure you hear a “click” sound to indicate that the dust bin plate is fully latched. Place dust bin unit back into vacuum cleaner by inserting the bottom first and tilting back. Refer to dust bin cleaning (pg. 10). Pre-Filter Tab 12 REPLACING HEPA EXHAUST FILTER Buckle • The HEPA exhaust filter removes dirt from exhaust air. [. . . ] • Stretch the hose to maximum length and then allow the hose to return to its storage length. • Turn off and unplug the vacuum cleaner. Connection Pipe Hook Nozzle • Remove dust bin and check upper filter and dust intake for clogs. • If the dust bin, upper filter, dust intake connection and the hose areas are free of clogs, check the nozzle area. Upper Filter ・ If the above areas are free of clogs, check the Nozzle Hose area. Disconnect the top of the Nozzle Hose from Curved Wand Holder by gently pressing the top of the Nozzle Hose. [. . . ]