User manual PANASONIC NV-HD600

[. . . ] Touching internal parts of the VCR is dangerous, and may seriously damage it. Inserting Remote Control Batteries Insert the batteries with the polarity (+ and -) correctly aligned. Cautions before you operate this VCR Avoid: · Humidity and dust. (Disconnect the aerial plug from the VCR during lightning storms. ) · Anything heavy on the VCR. · Using a cell phone near the VCR because doing so may cause noise to adversely affect the picture and sound. [. . . ] (See page 15. ) jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jj/jj jj/jj jj/jj jj jj jj jj jj jj jj jj jj:jj jj:jj jj:jj jj jj jj jj jj jj jj jj jj:jj jj:jj jj:jj jj jj jj jj jj jj jj jj jjj jjj jjj jjj jjj jjj jjj 27/10 20:00 21:30 ON 14 If [ss] Appears under [Pos/Name] after Entering a SHOWVIEW Number Pos/Name stands for Programme Position/TV Station Name. Normally, the name of the TV station or the number of the programme position is displayed under [Pos/Name]. However, if the [ss] indication appears, follow the operation steps below. Press the [CH] (12) repeatedly to select the programme position on which the TV programme to be recorded will be broadcast. After you have entered the information of a TV station, it remains stored in the VCR's memory, and you do not need to enter it again in the future. To Check, Change or Cancel Timer Recording Programmings 1) Press the [PROG. /CHECK] (14) to display the timer recording programmings on the TV screen. · When the VCR is in the timer recording standby mode for a VPS/PDC recording, the On Screen Display may be distorted. 2) Press the [Cursor] (38) 34 to select the programming that you want to change or cancel. 4) To change or cancel timer recording programmings, use the [Cursor] (38) 3421, the [CH] (12), [DATE] (11), [ON] (10), [OFF] (22) or [CANCEL] (13). 6) Press the [EXIT] (27) to exit the On Screen Display. Notes: In some cases, for example as listed below, the programming of a timer recording remains stored in the memory until 4 a. m. · When a timer recording was not performed up to the TV programme's ending time because the remaining tape time was not sufficient. · When you have stopped the timer recording while it was being performed. Setting the Recording Date/Day(s) Press the [DATE] (11) to select the recording date (1 to 31), daily timer recording date (Su­Sa, Mo­Sa or Mo­Fr) or weekly timer recording date (Su to Sa). 5) Press the [TIMER] (20) to switch the VCR over to the timer recording stand-by mode. Note: · Check that the [Á] is lit on the VCR display. (See page 15. ) Protecting programmes 1) Press the [I-TIMER] (15) to display the menu. 2) Press the [Cursor] (38) 43 to select the programme details that you want to protect, then press the [Cursor] (38) 1 to lock it. Locked programmes cannot be deleted. INTELLIGENT TIMER Panasonic VCR 27 / 10 / 02 Pos Name ZDF ARD ¢¢¢05 Date 27/10 27/10 28/10 Start Stop 20:00 21:30 20:00 21:30 10:30 11:30 VPS PDC SP SP EP ON ON sss Releasing the protection 1) Press the [I-TIMER] (15) to display the menu. 2) Press the [Cursor] (38) 43 to select the programme details that you want to release, then press the [Cursor] (38) 2. The lock symbol disappears. INTELLIGENT TIMER Panasonic VCR 27/ 10/ 02 Pos Name Date ZDF 27/10 Start 20:00 Stop 21:30 VPS PDC SP ON Pos Name Date ZDF 27/10 Start 20:00 Stop 21:30 VPS PDC SP ON Timer recording Pos Start Stop Name DATE ON OFF 1. jjjjj Panasonic VCR 1/2 VPS PDC SP jj jj jj jj jj jj jj 27/10 jj/jj jj/jj jj/jj jj/jj jj/jj jj/jj jj/jj 20:00 jj:jj jj:jj jj:jj jj:jj jj:jj jj:jj jj:jj 21:30 jj:jj jj:jj jj:jj jj:jj jj:jj jj:jj jj:jj ON jjj jjj jjj jjj jjj jjj jjj Total (SP) 90min Deleting the recording details Locked programmes must be unlocked before they can be deleted (see above for details). Press the [Cursor] (38) 43 to select the programme details that you want to delete, then press the [CANCEL] (13). Notes: · The Intelligent Timer Function can memorise the details of up to 8 timer recordings. If further timer recordings are made the Intelligent Timer Function will memorise the details of the new recording and the details of the oldest recording will be lost. To prevent losing a regularly used programme make sure the programme details are locked (see above). · When Auto Setup Restart, Download Restart, shipping condition or etc. [. . . ] · No programme was recorded because the AV input was selected on the VCR. Select the programme position of the desired TV programme. [The VCR picture does not appear on the TV screen. ] · The RF output channel is set to [ss]. (See page 8. ) [Timer recording does not work correctly. ] · Time and date are not set or they are set incorrectly. · The starting time or ending time of the timer recording were not programmed correctly. [. . . ]