User manual PANASONIC PT-D3500U

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D3500U Read these instructions completely before operating this unit. TQBJ 0178 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D3500U Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. WARNUNG- ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GERÄT NICHT ÖFFNEN. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the Product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Choose the appropriate aspect ratio carefully to match that of the original picture. Note · If the picture size is compressed or enlarged by using the 16:9 aspect ratio when the projector is used for profitable purpose or in the presence of an audience (for example, in a coffee shop or at a hotel etc. ), it may infringe the rights of the copyright owner of the original picture. · If a picture with the standard (4:3) aspect ratio is projected at a wide aspect ratio, parts of the picture may run over the screen bounds or the overall picture may be distorted. To view the picture at its original aspect ratio, choose the standard 4:3 aspect ratio. KEYSTONE KEYSTONE : Keystone distortion can be corrected only along either horizontal bound of the picture. button: button: · Keystone distortion can be corrected to ±30° of the angle of tilt for the projector. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. · The picture size will also change when correction of keystone distortion is carried out. LINEARITY : After you are finished with keystone adjustment, adjust vertical linearity with the or button. Linearity is not adjustable if no correction was made to keystone distortion. Note 31 How to use ADVANCED MENU ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POS. 1 RASTER POSITION SXGA MODE SXGA SELSCT RETRN ENTER INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" and "DISPLAY LINES" Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. Note · The abovementioned vertical stripes will not appear on the screen when all signals are input. · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. DIGITAL CINEMA REALITY (Only for input of S-Video/ Video/ YPBPR [480i, 576i] signals. ) ON: Set at ON when you need to faithfully capture images shot at 24 frames per second as in movies. OFF: Set at OFF when unnatural images are obtained in the ON status. BLANKING You can perform fine adjustments for blanking if noise appears at the ends of the screen or the image protrudes out of the screen during image projection using a video deck and so on. For upper adjustment For lower adjustment CLAMP POS. (For RGB/ YPBPR signals only) Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. The optimal value for the clamp position adjustment · If dark areas are crushed: The optimal value is the point where the dark area is best improved. · If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. Note For left adjustment For right adjustment · The clamp position can be adjusted only when the RGB signal input is applied with RGB1 and RGB2 IN. RASTER POSITION When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. [. . . ] Faites attention que votre main ne glisse pas en utilisant le tournevis. Attention · La lampe est une pièce en option. Contactez le revendeur. Bloc de lampe de rechange, modèle n°: ET-LAD35 (une ampoule) Valeurs nominales: 300 W Bloc de lampe longue durée, modèle n°: ET-LAD35L (une ampoule) Valeurs nominales : 160 W · Des lampes autres que celles spécifiées ci-dessus ne sont pas utilisables. Utilisez la lampe spécifiée. Période de remplacement de la lampe La lampe utilisée comme source lumineuse dans le projecteur a une vie de service de 1 500 heures 1 (quand la sortie de la lampe est HAUT). Il peut arriver que la lampe soit épuisée (ne s'allume pas) à 1 500 heures 1 selon les caractéristiques des lampes individuelles et les conditions de travail (la vie de service des lampes peut être réduite par le nombre d'allumages et les intervalles entre les allumages). [. . . ]