User manual PANASONIC PT-D5600UL

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D5600U PT-D5600UL PT-DW5000U PT-DW5000UL Read these instructions completely before operating this unit. TQBJ 0200 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. WARNUNG- ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GERÄT NICHT ÖFFNEN. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the Product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. · Automatic adjustment is not available if signals having a dot clock frequency of more than 108 MHz are supplied. DIGITAL CINEMA REALITY (Only for input of S-Video/ Video/ YPBPR [480i, 576i] signals. ) Set at ON when you need to faithfully capture images shot at 24 frames per second as in movies. ON: BLANKING You can perform fine adjustments for blanking if noise appears at the ends of the screen or the image protrudes out of the screen during image projection using a video deck and so on. : Adjust the blanking width. CLAMP POS. For upper adjustment For lower adjustment (For RGB/ YPBPR signals only) Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. The optimal value for the clamp position adjustment · If dark areas are crushed: The optimal value is the point where the dark area is best improved. · If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. Note · The clamp position can be adjusted only when the RGB signal input is applied with RGB1 and RGB2 IN. For left adjustment For right adjustment 32 Changing the display language RASTER POSITION When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. : These adjust the value in the vertical direction. SELECT ENTER RETRN LANGUAGE ENGLISH Currently chosen language is displayed here. XGA MODE This mode takes effect only when XGA (RGB) signals are input. XGA : Standard setting WXGA : Select this mode when WXGA signals are input. Menus, setting items, adjustment screens, and control button names will be displayed in the language the user chooses. The available languages are: ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, , , , . Note · The projector's on-screen display is set to the English language by default. SXGA MODE This mode takes effect only when SXGA (RGB) signals are input. SXGA : Standard setting SXGA+: Select this when the screen is cut off. 33 OPTION1 settings OPTION1 COLOR CORRECTION CONTRAST MODE AUTO SIGNAL OFF BACK COLOR BLACK SUB MEMORY LIST DVI EDID EDID2:PC SELECT ENTER RETRN SUB MEMORY LIST Multiple sets of image adjustment data (PICTURE, POSITION, ADVANCED MENU adjustment values) for the same kind of signal can be registered. SUB MEMORY LIST -- : RGB1­XGA60 1: 2: 3: 4: 5: 6: 7: 8: SELECT STORE RETRN COLOR CORRECTION OFF : Standard setting USER : The six colors of red, green, blue, cyan, magenta and yellow can be adjusted and registered for each of four signal systems: Video, S-Video, RGB and YPBPR. Press the ENTER button to make the detailed settings. COLOR CORRECTION RGB R G B Cy Mg Ye SELECT ADJ 0 0 0 0 0 0 RETRN Registering in sub memory Select the sub memory number to be registered using the buttons. Note · Sub memories range from 1 to 8. The current signal system is displayed. How to select sub memory Select sub memory number (1 to 8) using the buttons. Note · You cannot select sub memory of a different signal system. CONTRAST MODE There are two modes for adjusting to the operating environment. HIGH : The contrast is set to maximum and the brightness to normal. How to erase sub memory Select sub memory number (1 to 8) corresponding to sub memory to be erased using buttons. When the indicator of sub memory to be erased flashes, press the ENTER button. AUTO SIGNAL The position where the screen is displayed can be adjusted automatically without pressing the AUTO SETUP button on the remote control each time signals are input when signals are input frequently such as when the projector is used at a conference. ON : Auto setup is performed automatically when the video signals of the images being projected have changed. OFF : The input auto setup function is set to OFF. DVI EDID Set EDID to match the device connected. Mode EDID1 Matching Signal 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i VGA60, SVGA60, XGA50, XGA60, XGA70, XGA85, WXGA768/50, WXGA768/60, SXGA60 BACK COLOR You can set the colors of the screen when no signal is input to the projector. BLACK: Set screen color to black. EDID2:PC 34 OPTION2 settings OPTION2 ID FRONT/REAR DESK/CEILING LAMP SELECT LAMP POWER RS232C SYSTEM INFORMATION FAN CONTROL1 FAN CONTROL2 FUNC1 AUTO POW. [. . . ] Il est donc fortement conseillé aux utilisateurs de conserver une ampoule de rechange. Si la lampe n'est pas remplacée après 1 300 heures 2 (avec la sortie de lampe réglée sur "FORTE"), l'alimentation sera automatiquement coupée à 1 500 heures 1, avec passage en mode d'attente. 1 500 heures 1 à partir de l'allumage initial, l'alimentation est automatiquement coupée environ 10 minutes plus tard, avec passage en mode d'attente, même si la lampe est allumée à nouveau. Indication après 1 300 heures 2 (avec la sortie de lampe réglée sur "FORTE") REMPLACER LAMPE Quand la lampe a été utilisée 1 300 heures 2, le témoin de lampe (LAMPE1 ou LAMPE2) s'allume, état d'attente y compris. Une indication sur écran apparaîtra également environ 30 secondes comme indiqué dans le diagramme de droite, recommandant le remplacement de la lampe. [. . . ]