User manual PANASONIC RX-CT980

[. . . ] USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ LASERSÄTEILYLLE. OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. [. . . ] The mode is also canceled if the CD tray is opened. Random play Plays the tracks once each in random order Press [PLAY MODE] before or during play to select " ". Each time the button is pressed No display (canceled) To cancel Press [PLAY MODE] to clear " ". The mode is also canceled if the CD tray is opened. ·Random play does not work when " " is displayed (press [ /CLEAR] first). ·Search can be done within tracks only. 10 RQT5142 Page 10 99. 9. 10, 10:03 PM CDs Program play: Select up to 36 tracks to play in the order you choose Preparation: Press [ /CLEAR] to switch to CD mode. Enter the track number with the numbered buttons. Press [ PORTABLE STEREO CD SYSTEM ]. All the tracks are played in the selected order. The program remains intact even if play is stopped or the unit is turned off. "Cd-P" appears when play is stopped to indicate the contents are in the memory. To cancel Press [ /CLEAR] while stopped. "CLEAR" is displayed, all the tracks are cleared, and program mode is canceled. The mode is also canceled if the CD tray is opened. "FULL" is displayed If 36 tracks have been programmed. "-- --:-- --" is displayed If the total play time of the program exceeds 100 minutes. You can still program and play tracks. To check the contents of the program While stopped Press [ ] or [ ]. Each time one of the buttons is pressed, a track and its order in the program are displayed. Program play does not work when " " is displayed (press [PLAY MODE] to clear it) ( page 10). Search can be done within tracks only. 11 RQT5142 Page 11 99. 9. 10, 10:03 PM Compact disc operations For tracks numbered 10 and over, press [10] then the two digits. ·Operations on the current deck stop when an operation is started on the other deck. Before recording Use household AC power or new batteries when recording to avoid poor recordings caused by the batteries running down. Televisions can cause interference to recordings made on this unit if the two are too close to each other. Selection of tapes for recording The unit automatically identifies the type of tape. NO Metal position tapes can be used, but the unit will not be able to record or erase them correctly. Volume and sound quality in recording ·Recording level is set automatically. ·Recordings are unaffected by changes to sound quality. Selecting reverse mode Remote control only Side A Press [REV MODE]. and : Both sides record (top side : One side only records. bottom side). Tab for side "B" Tab for side "A" To re-record Erasing recordings Hi-position tape Insert the cassette with the side to be erased facing up. Press [ ]. Normal tape Recording operations Detection hole Erasure prevention The illustration shows how to remove the tabs to prevent recording. To record on the tape again, cover as shown, being careful not to cover the high position discrimination hole. To display the tape counter while recording Remote control only Press [DISPLAY]. Each time the button is pressed in CD, Radio, or AUX mode Present state (e. g. , elapsed play time of CD) To reset the tape counter Press [C-RESET]. The counter resets to "000". Present time Your attention is drawn to the fact that recording prerecorded tapes or discs or other published or broadcast material may infringe copyright laws. Tape counter 16 RQT5142 Page 16 99. 9. 10, 10:06 PM Recording CDs (Deck 2 only) Preparation: ·Insert a CD ( page 9). ·To record from the beginning of the tape Wind on the leader tape. Recording tape Leader tape Press [ DECK 2] to open the deck and load a cassette. Recording starts from the side facing up Close deck by hand. (Play direction automatically switches to " the deck is closed. ) " when Press [ TAPE/CD] to switch to CD mode. Each time the button is pressed CD TAPE Press [ ] to start recording. CD play and recording start at the same time. [. . . ] To change the source Turn the unit on, choose the source and press [ to turn the timer on ( step ). PLAY/REC] You can enjoy other sources after you have set the timer. The timer will come on under the same conditions the unit was in when [ PLAY/REC] is pressed to turn the timer on ( step ). Before turning the power off, check tape direction if you played cassettes. The sleep timer Remote control only Set the unit to stop and turn off after a certain time. While listening to a CD, a cassette, or the radio. Press [SLEEP] to select the time (in minutes). Each time the button is pressed SLEEP 30 SLEEP 60 SLEEP 90 SLEEP OFF SLEEP 120 To cancel Press [SLEEP] to select "SLEEP OFF". To check the remaining time Press [SLEEP] once. The remaining time is shown for about 5 seconds. To change the time. Press [SLEEP] to select the new time. [. . . ]