User manual PARTNER COLIBRI 25

[. . . ] Use unleaded or quality leaded petrol and two-stroke oil mixed at a ratio of 2. 5%. Sound power level Max speed of output axle, rpm 2 SAFETY RULES When using gardening appliances, basic safety precautions should always be followed to reduce the risk of fire and serious injury. Operator is responsible for following instructions and warnings on unit and in manual. Be thoroughly familiar with the controls and the proper use of the unit. [. . . ] To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. Choke Lever Primer Bulb Muffler 1. Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times. As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE. Pull starter rope sharply until engine runs, but no more than 6 pulls. If the engine doesn't start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. Once the engine starts, allow it to run 10 seconds, then move the choke lever to OFF CHOKE. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls. 9. HOW TO STOP YOUR UNIT S To stop the engine, move the ON/OFF switch to the OFF position. HOW TO START YOUR UNIT WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns. STARTING A COLD ENGINE (or a warm engine after running out of fuel) Starting Position STARTING A WARM ENGINE 1. The metal line limiter blade attached to the guard will cut the line to the proper length. Right Wrong S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. S For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially: S During light duty cutting. S Near objects around which the line canwrap such as small posts, trees or fence wire. TRIMMING - Hold the bottom of the trimmer head about 80 mm above the ground and at an angle. Other sizes and shapes of line will not advance properly and will result in improper cutting head function or can cause serious injury. Wire can break off during cutting and become a dangerous missile that can cause serious injury. 3 in. (8 cm) Above Ground SCALPING - The scalping technique removes unwanted vegetation. Hold the bottom of the trimmer head about 80 mm above the groundand at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. [. . . ] : +1 903 223 4100, declare under sole responsibility that the Partner model Colibri 25 grass trimmer was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2003-210N00001 and onwards, conforms to the provisions of the DIRECTIVE. The measured sound power is 108 dB and the guaranteedsound power is 112 dB. Bounds, Director Product Safety and Standards DECLARATION OF CONFORMITY relating to 98/37/EC EC Declaration of Conformity (Directive 98/37/EC, Annex II, A) (Only applies to Europe) We, Electrolux Home Products, Inc. , Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, Declare under sole responsibility that the Partner model Colibri 25 grass trimmer from serial numbers 2003-210N00001 and onwards, follows the provisions of the DIRECTIVES: 98/37/EC (machinery) and 89/336/EEC (electromagnetic compatibility), including amendments and is in conformity with the following standards: EN 292- 2, EN ISO 11806:1997 and CISPR 12. [. . . ]