User manual PHILIPS 43266-56-16

[. . . ] Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardization for early integration in its products. General information • To prevent fire or shock hazard: Always keep this product dry. Do not expose it to excessive heat by heating equipment or direct sunlight. No naked flame sources, such as lighted candles, should be placed on the apparatus. [. . . ] Do not operate or store the product in a place where temperature is below 0°C (32°F) or above 40°C (104°F) as this may shorten the battery life. The mains plug of AC/DC adaptor is used as the disconnect device, the disconnect device shall be readily operable. Be sure to observe the following guidelines when using your headphones. • • Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can’t hear what’s around you. You should use caution or temporarily discontinue use in potentially hazardous situations. Excessive sound pressure from earphones and headphones can cause hearing loss. • • • • • • • • Electric-, Magnetic- and Electromagnetic Fields (EMF) 1. Royal Philips Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals. •• AAA alkaline batteries can be used to operate the headphones. •• If no audio input for over 10 minutes, the transmitter automatically turns to standby. •• The docking station does not transmit audio signal during charge. •• Digital input only supports PCM (pulse code modulation). 1 2 3 Press and hold on the right headphone for 2 seconds to power on the headphones (Fig. H). Press the 3D SOUND button on the right headphone to activate/deactivate the 3D sound function (Fig. I). »» The LED on the transmitter turns on. Tip •• You can also adjust the volume on the audio device. 1 2 3 4 • Install/Replace the supplied batteries (Fig. B). In ANALOGUE mode, connect the audio device to LINE IN sockets, then adjust ATT (Attenuation of audio input signal) (Fig. F). • For portable CD player, MP3 player or other devices with 3. 5mm triport socket output, connect with RCA to RCA cable (provided) and RCA to 3. 5mm plug adaptor (not provided), then switch ATT to 0dB. [. . . ] • For Hi-Fi, TV, DVD player or other devices with RCA socket output, connect with RCA to RCA cable (provided), then switch ATT to -8dB. • In DIGITAL mode, connect the digital audio device to DIGITAL IN COAXIAL socket with coaxial cable (not provided) (Fig. G). EN 5 L L 2 sec www. philips. com/w elcome Quick start guide 6 EN 4 LED indications Situation LED Searching Connection established Standby Low battery Charging Fully charged Non NiMH batteries 3D sound activated 3D sound deactivated Transmitter Analogue/Digital White Fast blinking Blinking Off --Off --------Headphones Charging Red ----Off --Blinking On Off ----3D sound White --------------On Off Red Fast blinking Blinking --Fast blinking ----------- EN 7 5 Sound indications Situation Low battery Turn the volume to maximum/minimum level Sound signal One “Beep” per 10 seconds Alert tone “Beep” 8 EN 6 Product information Transmitter System Modulation Carrier frequency Channels Radiated output power Effective transmission range Input Level Power requirements Headphones Playback frequency range Signal/Noise ratio Distortion Channel Separation Impedance Power Requirements Operating time 17 - 24, 000 Hz 89 dB Nominal < 0. 5% THD (Total Harmonic Distortion) 60 dB 32 ohm 2 x 700 mAh rechargeable NiMH batteries (supplied) or commercially available (AAA) dry batteries ~ up to 20 hours (actual result may vary) Radio Frequency (RF) MSK digital 2, 400 - 2, 483. 5 MHz 15 (auto-switching) 10 mW Approx. 100 meters (depending on ambient conditions) 800 mV (0 dB); 2 V (-8 dB) DC 5 V; 300 mA (from the supplied AC power adaptor) EN 9 7 Adaptor specification Region Europe (except U. K. ) U. K. /H. K. Adaptor type Input voltage number YLS0051A-E050030 100-240V~ S003IV0500030 100-240V~ YLS0051A-U050030 100-240V~ S003IB0500030 100-240V~ Output voltage 5V 5V 5V 5V , 300mA , 300mA , 300mA , 300mA Input frequency 50/60Hz 50/60Hz 50/60Hz 50/60Hz 10 EN 8 Frequently asked questions (FAQ) 1. [. . . ]