User manual PLEXTOR 12-20B

[. . . ] ---- CHAPTER 8 ---- Hardware Installation By itself, your CD-ROM drive is incapable of communicating with your computer. You must use a hardware link that enables your drive to ``talk'' with the rest of your computer. If you own a PC, there are four ways in which you can make the SCSI connection: 1) Use a separate SCSI interface board. We recommend using a 32-bit PCI bus mastering SCSI interface board to maximize the drive's potential. [. . . ] The two cable connections that you must make are: 1) SCSI cable 2) power cable Audio Connector SCSI Interface Connector Jumpers Personal Computer Power Connector Power Supply from Personal Computer SCSI Ribbon Cable SCSI Host Adapter The SCSI cable you will need is included with your drive. It is a standard 50-pin flat ribbon cable with three connectors (one at each end and one in the middle). If you are connecting the host adapter to your Plextor drive only, use the two end connectors and ignore the one in the middle. If you already have one other SCSI peripheral (such as a hard disk), and your existing cable has only two connectors, remove the cable and replace it with the cable provided by Plextor. Connect the SCSI host adapter to a connection on either end of the cable. Connect the two peripherals to the other two connectors (one at the middle connector and one at the end of the cable). Refer to Chapter 7 of this manual for setting the termination of the devices. If you have more than one other internal SCSI peripheral (besides your Plextor drive), you will need to acquire a SCSI ribbon cable with more connectors (one connector for each internal SCSI device, plus an additional connector for the host adapter----refer to Chapter 3). Refer to Chapter 7 of this manual for setting the termination of the devices. CAUTION: It is easy to accidentally plug your SCSI ribbon cable upside down into both your drive and SCSI interface board. Accordingly, be sure you match the red stripe along one side of the SCSI cable to pin 1 on the interface board and pin 1 on the drive (as shown on the next page). Each connector on the ribbon cable has a ``key'' in the middle. This key should fit into a slot in the middle of each connector of the interface board, your 12/20PleX CD-ROM drive, and any other SCSI peripherals. DC Power Supply Pin 1 28 12/20PLEX OPERATION MANUAL CHAPTER 8 ---- Hardware Installation Double-check your work; you must ensure the side of the SCSI cable with the red stripe is matched to pin 1 on the interface board and on the drive. #1 To Pin #1 Either end of the cable may be connected to either the CD-ROM drive or to the SCSI interface board Pin #1 The easiest way to install your SCSI cable is to plug it into the SCSI connector on the rear panel of the drive before you insert the drive into your computer. Then you can thread the cable through the front of the open bay you plan to use and back toward the SCSI interface board. Connect the cable to your SCSI interface board and finish mounting your drive in the proper position. Review your current computer setup to see if the potential for conflicts exists. If so, make necessary switch, dial, and/or terminator changes. YOUR OBJECTIVE: YOUR METHOD: If you are installing a single 12/20PleX external drive, and you have no other SCSI peripherals attached to your system, you should leave the switches, dial, and terminator found on the rear panel of your drive at their factory settings. If you do have additional SCSI peripherals (e. g. , scanner, printer) attached to your computer, you may need to change your switch, dial, and terminator settings. If you are installing a single 12/20PleX external drive, connect it as shown on the next page: 30 12/20PLEX OPERATION MANUAL CHAPTER 8 ---- Hardware Installation PC Connection SCSI Interface Board SCSI Cable Secure to controller by pushing gently until cable ``snaps'' into place. X PX-20TSe Rear Panel Personal Computer AC Power Supply Mac Connection (rear view of a Mac) Plugs into X (above) SCSI Cable Plugs into Y Y 12/20PLEX OPERATION MANUAL 31 CHAPTER 8 ---- Hardware Installation If you are installing more than one PX-20TSe external drive (or one PX-20TSe and other external SCSI peripherals), connect them as shown below: PC Connection SCSI Cable Personal Computer X 50-pin Centronics Termination DISABLED SCSI Interface Board Daisy Chain Cable Termination DISABLED Termination ENABLED Mac Connection (rear view of a Mac) Plugs into X (above) SCSI Cable Plugs into Y Y 32 12/20PLEX OPERATION MANUAL CHAPTER 8 ---- Hardware Installation NOTE: The following section is only for those installing a soundboard in their PC. If you are not using a soundboard, skip to Chapter 9. Soundboard Installation YOUR TASK: YOUR OBJECTIVE: YOUR METHOD: Install a soundboard in your PC. [. . . ] (See listing of key contact phone/fax/BBS numbers on page 61. ) The OS/2 device driver files that you need from your SCSI interface board's manufacturer end with an ``. ADD'' extension. They need to be copied into the CONFIG. SYS file on the OS/2 installation floppy disk. Your SCSI interface board manufacturer will provide you with specific instructions. Adding CD-ROM Support After OS/2 Has Already Been Installed 1) You first need to verify that your SCSI interface board is supported by OS/2. Check your OS/2 manual, and the README file on the floppy disk that comes with the OS/2 CD-ROM, for information on which SCSI interface boards OS/2 supports. [. . . ]