User manual POLAROID 1913-TDXB

[. . . ] HD Widescreen LCD TV/DVD Combo 1513-TDXB and 1913-TDXB ©2007 by . All rights reserved. "Polaroid" and "Polaroid and Pixel" are trademarks of Polaroid Corporation, Waltham, MA, USA. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions. For service, support and warranty information, visit www. polaroid. com. This product contains electrical or electronic materials. [. . . ] (Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown, consult your cable TV company. ) For more specific instructions on installing cable TV, consult your cable TV company. One possible method of connecting the converter/descrambler provided by your cable TV company is shown in the diagram below. RF switch (not included) A IN B OUT 2 set signal splitter (not included) Cable TV Line VHF/UHF IN Cable TV converter/ descrambler (not included) The RF switch (not included) is required to provide two inputs (A and B). Setting the RF switch to position A allows viewing of all unscrambled channels by using the TV channel keys. Setting the RF switch to position B allows viewing of all scrambled channels via the converter/descrambler by using the converter channel keys. 18 Chapter 2 Installing the LCD TV Use a supplied antenna cable to connect the TV signal to the LCD TV's TV CABLE terminal. ENGLISH VHF/UHF IN Connect the DC plug of the AC-DC adapter to the DC 12V port at the back of the TV. Connect the power cord to wall outlet. Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The POWER button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. Press the INPUT button on the remote to display the Input List. Use the buttons to select TV and press the OK button. Main TV(CABLE/AIR) VIDEO1 (AV) VIDEO2 (S-VIDEO) VIDEO3 (YPbPr) DVD USB CARD READER VIDEO4 (HDMI) COMPUTER(VGA) 19 Chapter 2 Installing the LCD TV Press the MENU button on the remote control to display the Main menu, and use the buttons to select the TV. Channel Scan Tuner Mode Channel Skip Time Zone Cable Eastern Time TV Select Exit Press the button to select Channel Scan, and press the OK button. Press the MENU button at any time to interrupt the memorization process. (the list cannot be created if interrupted) The Channel Scanning will create a list of receivable channels for the current input (antenna or cable). You will be required to run Channel Scanning for each RF input to create a list of available channels from both inputs. Press the OK button to display the received channel list, then press to select a channel. Or, use the (INPUT button) with 0-9 buttons to select digital channel( for example 9. 1) Channel List 5-2 RF5-2 9-1 KQED-HD 9-2 KOED-SD 8 CCT 12 13 15 The digital main channel might include many subchannels (for example 9-1, 92. . ) that are showing program at the same time. 20 Chapter 2 Installing the LCD TV Connecting an A/V Device with Composite Connector ENGLISH Rear of TV HDMI IN Y YPbPr IN Pb Pr VIDEO S-VIDEO COAXIAL VHF/UHF IN VGA IN VGA LINE IN R GAME CONSOLE AUDIO Cable VIDEO OUT L R D V D PLA YER AV Cable Use a composite cable to connect the external A/V device's composite video/audio jacks to the LCD TV's VIDEO IN jacks. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To view the A/V device's with component input, press the INPUT button on the remote to select VIDEO1. Not all A/V devices have the ability to connect to a TV. Please check your A/V devices user guide for compatibility. 21 Chapter 2 Installing the LCD TV Connecting an A/V Device with S-Video Connector Rear of TV HDMI IN Y YPbPr IN Pb Pr VIDEO S-VIDEO COAXIAL VHF/UHF IN VGA IN VGA LINE IN R GAME CONSOLE AUDIO Cable S-VIDEO OUT L R D V D PLA YER S-VIDEO Cable Use an audio cable to connect the external A/V device's audio output jacks to the LCD TV's audio inputs. Use a S-Video cable to connect the external A/V device's S-Video output jack to the LCD TV's S-Video IN input jack. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To view the A/V device's with component input, press the INPUT button on the remote to select VIDEO2. 22 Chapter 2 Installing the LCD TV Connecting an A/V Device with Component(YPbPr) Connector ENGLISH Rear of TV HDMI IN Y YPbPr IN Pb Pr VIDEO S-VIDEO COAXIAL VHF/UHF IN VGA IN VGA LINE IN L R L R Pb Cb Pr Cr COMPONENT OUT GAME CONSOLE AUDIO Cable R L COMPONENT Cable Pr/Cr Pb Pb/Pb Pr D V D PLA YER Y Not all A/V device have the ability to connect to a TV. Please check your A/V device user guide for compatibility. Use a component cable to connect the external A/V device's component output jacks to the LCD TV's YPbPr IN input jacks. Use an audio cable to connect the external A/V device's component audio jacks to the LCD TV's audio input jacks. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To view the A/V device's with component input, press the INPUT button on the remote to select VIDEO3. The component video jacks on your A/V device are sometimes labeled YPbPr, or YCbCr. For an explanation of component video, see your A/V device's user guide. 23 Chapter 2 Installing the LCD TV Connecting an AV Equipment with HDMI Connector Rear of TV HDMI IN Y YPbPr IN Pb Pr VIDEO S-VIDEO COAXIAL VHF/UHF IN VGA IN VGA LINE IN L R L R HDMI Cable AV EQUIPMENT Use a HDMI cable to connect the AV equipment's HDMI output jack to the LCD TV's HDMI IN jacks. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. Press the Input button on the remote to select VIDEO4. The HDMI connector provides both video and audio signals, it's not necessary to connect the audio cable. 24 Chapter 2 Installing the LCD TV Connecting an AV Equipment with DVI Connector Rear of TV ENGLISH HDMI IN Y YPbPr IN Pb Pr VIDEO S-VIDEO COAXIAL VHF/UHF IN VGA IN VGA LINE IN L R L R AUDIO Cable AUD IO L R DVI IN HDMI-to-DVI Cable AV EQUIPMENT Use a HDMI-to-DVI cable to connect the AV equipment's DVI output jack to the LCD TV's HDMI IN jacks. [. . . ] If it does not, repeat steps 3­5, trying each code for your brand until you find one that works. If you cannot find a code that works, see "Searching for Your Code". Repeat steps 1­5 for the other devices you want to control. For future reference, write down each working device code below: AUX Code: CBL Code: CD Code: DVD Code: SAT Code: TNR Code: VCR Code: Press set to save and exit. 52 Programming Your Remote Control Searching for your Code If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code: ENGLISH Press a device key once. Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). [. . . ]