User manual POLAROID 2626-TLMB

[. . . ] TABLE OF CONTENTS IMPORTANT SAFETY AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ENGLISH GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NOTE 3 : Cables not included. 13 CONTROLS & ADJUSTMENTS General Adjustments Turning the LCD TV On and Off Turn On Connect the Power Cord into the AC IN located in the back of the display and the other end to the power outlet on the wall. Press the Power button on the remote control or right side of the TV to turn the TV on. The power status light found in the lower right corner of the TV indicates the following : BLUE LIGHT power on PURPLE LIGHT Standby, power saving (only available in PC mode) RED LIGHT power off AC IN BLUE Turn Off Press the power button on the remote control or right side of the TV to turn the TV off. RED 14 Power Consumption Power Consumption is a power management technique which helps to set up the POWER OFF status for the LCD TV set. There are three modes: Low/Medium/High Low : The power consumption is no more than 5W in the POWER OFF status. Medium : The power consumption within the first hour is less than 35W and you can turn on TV around 3 seconds. After one hour, the power consumption is switched to around 5W and it takes 12-15 seconds to turn on the LCD TV. High : The LCD TV set can be turned immediately and the maximum power consumption would be less than 35W. ENGLISH 1. Press EXIT button to exit all menu or press button to return to the previous screen. 15 Initial Setup When the system powers on for the first time, the initial auto installation is enabled. Use the buttons to select the language you prefer, and press OK button to continue. Time Zone Selection 2. Press the buttons to select on your Time Zone, and press OK button to continue. NOTE : It takes around 5 to 30 minutes to finish the Initial Setup process. The time taken for Initial Setup is varied according to the number of scanned channels. 16 Daylight Saving 3. Press buttons to set the Daylight Savings, and press OK button to continue. ENGLISH Input Source Selection 4. Press buttons to select the source for your TV signal, and press OK button to start scanning. If the user selects Antenna, the next setup wizard is presented. 17 When "Cable" Source is selected, please toggle Automatic, STD, IRC, or HRC. To have all channels completely scanned, please select STD, IRC or HRC. 5. After all the available channels are stored, the channel list will appear. 6. Press OK and start to watch TV. 18 Reset the features The user can reset all settings back to factory settings, including the channel map, all Program Info, Favorite channel lists, etc. If a PIN is set, the PIN entry dialog is displayed before the "Reset All" Settings dialog box, even if Locks are temporarily off. Press the buttons to select Settings and press / buttons to access the RESET ALL screen. 3. Press the to select "Reset" and OK buttons to reset all settings. 19 Changing Channels Using the Channel buttons When you press the CH/buttons, the TV changes channels in sequence. Using the Last button to select the previous channel To quickly switch between two channels, tune to one channel, then use the number button to select the second channel. Then press the LAST button to quickly alternate between them. Adjusting the Volume Using Volume Control Press the VOL + / ­ buttons to increase or decrease the volume. [. . . ] As the Remote searches its library, it starts with the most popular device in the category and works through to the end. To cycle through each available device code and sample its functions: ENGLISH Mode <<SET UP>> (2 blinks) [9] [9] [1] (2 blinks) <Ch> <Ch> . . . <<SET UP>> (2 blinks) STEP 1 Select the [MODE] by pressing DVD, CAB/SAT, or AUX. STEP 2 Depress and hold SET UP button for a minimum of 3 seconds until LED blinks twice. [. . . ]