User manual POLAROID 3211-TLXB

[. . . ] All rights reserved. "Polaroid" and "Polaroid and Pixel" are trademarks of Polaroid Corporation, Waltham, MA, USA. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions. For service, support and warranty information, visit www. polaroid. com. This product contains electrical or electronic materials. The presence of these materials may, if not disposed of properly, have potential adverse effects on the environment and human health. [. . . ] In the event of an electrical storm or power outage the safety fuse is designed to protect your TV. If your TV has no power, check the fuse by prying the cover off, following the illustration below. If the fuse is blown, visit your local hardware store and ask for a 4A 250V - 5x20mm Time Lag Fuse (Slow Blow) to replace the fuse. Firm Plastic Prying Tool (Using a metal tool may cause shock) Back of TV 4A 250V 5x20mm Fuse BE SURE TO UNPLUG AC POWER CORD BEFORE REMOVING THE FUSE. Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The POWER button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. 20 Chapter 2 Installing the LCD TV Press the button on the remote to turn on the LCD TV. Main TV(CABLE/AIR) VIDEO1 (SIDE) VIDEO2 (REAR) VIDEO3 (S-VIDEO) VIDEO4 (YPbPr1) VIDEO5 (YPbPr2) VIDEO6 (HDMI1) VIDEO7 (HDMI2) COMPUTER(VGA) ENGLISH Press the INPUT button on the remote to display the Input List. Use the buttons to select TV and press the OK button. Channel Scan Tuner Mode Channel Skip Favorite List Time Zone Cable Eastern Time TV Select Exit Press the MENU button on the remote control to display the Main menu, and use the buttons to select the TV. Status: Scanning. . . . . Analog Channels: 25 Digital Channels: 0 Cable 47% The Channel Scanning will create a list of receivable channels for the current input (antenna or cable). You will be required to run Channel Scanning for each RF input to create a list of available channels from both inputs. Press the OK button to display the received channel list, then press to select a channel. Or, use the (INPUT button) with 0-9 buttons to select digital channel( for example 9. 1) Channel List 5-2 RF5-2 9-1 KQED-HD 9-2 KOED-SD 8 CCT 12 13 15 The digital main channel might include many subchannels (for example 9-1, 92. . ) that are showing program at the same time. 21 Chapter 2 Installing the LCD TV Connecting a VCR Rear of TV HDMI 2 IN HDMI 1 IN VGA IN AUDIO OUT YPbPr1 IN STEREO DIGITAL OPTICAL R HDTV/TV Air/CABLE AUDIO AUDIO Y Pb Pr AUDIO L R L R Y Pb Pr L L COAXIAL VHF/UHF IN VIDEO AUDIO VIDEO2 IN L R L R S-VIDEO AUDIO S-VIDEO IN L YPbPr2 IN AUDIO R R AUDIO Cable S-VIDEO Cable AV Cable METHOD A: Use a composite cable to connect the VCR's composite video/audio jacks to the LCD TV's VIDEO2 IN jacks. METHOD B: Use an audio cable to connect the VCR's audio output jacks to the LCD TV's audio inputs. Use a S-Video cable to connect the VCR's s-video output jack to the LCD TV's S-VIDEO IN input jack. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To watch a videotape, press the INPUT button on the remote to select VIDEO2( METHOD A), or VIDEO3 (METHOD B). Turn on your VCR and follow the instructions in your VCR's manual. 22 Chapter 2 Installing the LCD TV Connecting a Video Camera or Game console Rear of TV ENGLISH Right Side HDMI 2 IN VIDEO HDMI 1 IN VGA IN AUDIO OUT YPbPr1 IN STEREO DIGITAL OPTICAL R HDTV/TV Air/CABLE AUDIO L AUDIO Y Pb Pr AUDIO L R VIDEO1 IN R L R Y Pb Pr L L COAXIAL VHF/UHF IN VIDEO AUDIO VIDEO2 IN L R L R S-VIDEO AUDIO S-VIDEO IN L YPbPr2 IN AUDIO R R AUDIO Cable or S-VIDEO Cable GAME CONSOLE AV Cable METHOD A: Use a composite cable to connect the video camera's or game console's composite video/audio jacks to the LCD TV's VIDEO2 IN jacks or VIDEO1 IN jacks. METHOD B: Use an audio cable to connect the video camera's or game console's audio output jacks to the LCD TV's audio inputs. Use an S-Video cable to connect the video camera's or game console's s-video output jack to the LCD TV's S-VIDEO IN input jack. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To watch a video vis camera or game console, press the INPUT button on the remote to select VIDEO2/VIDEO1( METHOD A), or VIDEO3 (METHOD B). Not all cameras have the ability to connect to a TV. 23 Chapter 2 Installing the LCD TV Connecting a DVD Player Rear of TV VGA IN AUDIO OUT YPbPr1 IN AUDIO AUDIO Y Pb Pr AUDIO STEREO DIGITAL OPTICAL R HDTV/TV Air/CABLE HDMI 2 IN HDMI 1 IN L R L R Y Pb Pr L L COAXIAL VHF/UHF IN VIDEO AUDIO VIDEO2 IN L R L R S-VIDEO AUDIO S-VIDEO IN L YPbPr2 IN AUDIO R R or Pb Pr COMPONENT/AUDIO Cable AUDIO Cable S-VIDEO Cable AV Cable C Pb Pr D V D PLA YER METHOD A: Use a composite cable to connect the DVD player's composite video/audio jacks to the LCD TV's VIDEO2 IN jacks. METHOD B: Use an audio cable to connect the DVD player's audio output jacks to the LCD TV's audio inputs. [. . . ] If it does not, repeat steps 3­5, trying each code for your brand until you find one that works. If you cannot find a code that works, see "Searching for Your Code". Repeat steps 1­5 for the other devices you want to control. For future reference, write down each working device code below: AUX Code: CBL Code: CD Code: DVD Code: SAT Code: TNR Code: VCR Code: Press set to save and exit. 50 Programming Your Remote Control Searching for your Code If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code: ENGLISH Press a device key once. Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). [. . . ]