User manual POLAROID 3226-TLMB

[. . . ] TABLE OF CONTENTS IMPORTANT SAFETY AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ENGLISH GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The TV will power off automatically if an input source is not selected. 15 Power Consumption Power Consumption is a power management technique which helps to set up the POWER OFF status for the LCD TV set. There are three modes: Low/Medium/High Low : The power consumption is no more than 5W in the POWER OFF status. Medium : The power consumption within the first hour is less than 35W and you can turn on TV around 3 seconds. After one hour, the power consumption is switched to around 5W and it takes 12-15 seconds to turn on the LCD TV. High : The LCD TV set can be turned immediately and the maximum power consumption would be less than 35W. 1. Press EXIT button to exit all menu or press button to return to the previous screen. 16 Initial Setup When the system powers on for the first time, the initial auto installation is enabled. Use the buttons to select the language you prefer, and press OK button to continue. ENGLISH Time Zone Selection 2. Press the buttons to select on your Time Zone, and press OK button to continue. NOTE : It takes around 5 to 30 minutes to finish the Initial Setup process. The time taken for Initial Setup is varied according to the number of scanned channels. 17 Daylight Saving 3. Press buttons to set the Daylight Savings, and press OK button to continue. Input Source Selection 4. Press buttons to select the source for your TV signal, and press OK button to start scanning. If the user selects Antenna, the next setup wizard is presented. 18 When "Cable" Source is selected, please toggle Automatic, STD, IRC, or HRC. To have all channels completely scanned, please select STD, IRC or HRC. ENGLISH 5. After all the available channels are stored, the channel list will appear. 6. Press OK and start to watch TV. 19 Reset the features The user can reset all settings back to factory settings, including the channel map, all Program Info, Favorite channel lists, etc. If a PIN is set, the PIN entry dialog is displayed before the "Reset All" Settings dialog box, even if Locks are temporarily off. Press the buttons to select Settings and press / buttons to access the RESET ALL screen. 3. Press the to select "Reset" and OK buttons to reset all settings. 20 Changing Channels Using the Channel buttons When you press the CH/buttons, the TV changes channels in sequence. Using the Last button to select the previous channel To quickly switch between two channels, tune to one channel, then use the number button to select the second channel. Press the LAST button to quickly alternate between them. ENGLISH Adjusting the Volume Using Volume Control Press the VOL + / ­ buttons to increase or decrease the volume. Using Mute At any time, you can turn off the sound using the MUTE button. Press MUTE again or VOL + / ­ buttons to return audio back to the previous volume level. 21 Switching Source 1. [. . . ] STEP 5 Press SET UP button will store the new device code and returns to normal operation. The LED blinks twice in confirmation. Mode Device Assignment TV Locked to this TV (Default) DVD Universal VCR, DVD, PVR CAB/SAT Universal Cable, Satellite, Video Accessory AUX Universal Tuner, Amplifier, CD, Mini Disc. ------2 0 3 Example: [VCR ] <<SET UP>> (2 blinks) [9][9][1] (2 blinks) <Ch> <Ch>. . . [SET UP] (2 blinks). 54 Device Codes The following sections list the available device codes for each device mode button. [. . . ]