User manual POLAROID FCM-0710

[. . . ] 7" Under-the-Cabinet LCD TV FCM-0710 20060209 Important Safety Instructions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE. POWER SUPPLY: Connect the supplied adapter to the side of the Under-the-Cabinet LCD TV in the slot marked "Power In". If you have difficulty inserting the plug, turn it over and reinsert it. [. . . ] When connecting the supplied AM loop antenna, connect two black cords to AM and ground jacks as shown below. OUT DOOR FM ANTENNA EARTH WIRE · · · If the FM reception is poor, use a 75 coaxial cable to connect system to an outdoor FM antenna as above. If you connect the system with outdoor FM antenna, you should earth the system in order to avoid lightning strike. Do not connect the earth wire to gas pipe to prevent gas explosion. - 14 - System Connections Connecting To the Power Adapter This unit is powered via the switching power adapter (supplied). See the below figure for details: 1. Connect the AC adapter to jack marked with "DC 12V IN" on the rear panel of the unit. 2. 3. Plug the two-prong end of the power cord to the grounded electrical socket. When not using the unit, turn off the power of the unit first, and then unplug the power supply to prevent malfunctions. - 15 - Radio Function Radio Function Operation Press the FM or AM button to enter FM or AM radio mode. Then press the SEEK+/button on the remote control or the SEEK+/- button or / / button on the front panel for about 1. 5 seconds to start searching forward/backward from the current frequency. The frequency range of FM is from 87. 5MHz to 107. 9 MHz, frequency range of AM is from 520 kHz to 1710 kHz. Fine Tuning Press the SEEK+/- button on the remote control or the / button on the front panel once to fine tune the frequency forward/backward under radio mode. Semi-memorizing radio stations If you like a radio station and want to store it for later listening, press the MENU/SET on the remote control or the SET button on the front panel to memorize it. "SAVE 00" will be displayed on the display panel, "00" represents the default station number. There are two methods to organize the memorized stations: · Use the buttons to adjust the channel number for your preference, and then press the MENU/SET button or SET button again, the station will be memorized with the coded station number. · Press the MENU/SET button or the SET button again, the station will be automatically memorized with the default station number in sequence. You can store radio stations from 0 to 19, total 20FM or 20AM radio stations. If no buttons are pressed within 3 seconds when pressing the MENU/SET button first time, the frequency will appear on the display panel again, and the station will not be stored. Accessing memorized radio stations · First use the number buttons on the remote control for input, then press the ENT button for confirmation to go to the selected radio station directly; Or without pressing any button and wait a moment, it also goes to the selected radio station. · Press the , buttons on the remote control or front panel to select the radio stations forward and backward. When selecting the stations, the "CH 00" will appear on the display panel, where the "00" is the channel number of the stored radio station. After a few seconds, the "CH 00" disappears and the radio frequency will be displayed once again. - 16 - TV Function Basic Operation Connect the antenna to the antenna jack on the rear panel. If the unit is in standby mode, press the POWER button on the front panel to turn on the power. Press the TV button on the remote control or the front panel to shift to TV mode. Press the , buttons to select the channels forward or backward in sequence. [. . . ] Select Reset and press the ENT button to return to the factory default settings. First use the , buttons to highlight PICTURE, and then press the button on the remote control to exit from the setup menu. Note: Under AV mode, if there is no signal, the LCD screen will be blue. When connected to an AV signal source, make sure the type of the selected AV signal source is NTSC. - 21 - Installing the unit in Kitchen Note: Before installing the unit in the kitchen, please make all the connections. Installing the unit under a cabinet The unit may be installed in the kitchen with or without the spacers. [. . . ]