User manual POLAROID FLM-2011

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Connect the equipment into an outlet on a circuit which is different from what the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user authority to operate the equipment. WEEE This product contains electrical or electronic materials. The presence of these materials may, if not disposed of properly, have potential adverse effects on the environment and human health. [. . . ] (Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown, consult your cable TV company. ) For more specific instructions on installing cable TV, consult your cable TV company. One possible method of connecting the coverter/descrambler provided by your cable TV company is shown in the diagram below. RF switch (not included) A IN B OUT 2 set signal splitter (not included) Cable TV Line VHF/UHF IN Cable TV converter/ descrambler (not included) The RF switch (not included) is required to provide two inputs (A and B). Setting the RF switch to position A allows viewing of all unscrambled channels by using the TV channel keys. Setting the RF switch to position B allows viewing of all scrambled channels via the converter/descrambler by using the converter channel keys. 16 Chapter 2 Installing the LCD TV METHOD A: Use a supplied antenna cable to connect the NTSC signal to the LCD TV's TV CABLE terminal. ENGLISH TV CABLE HDTV AIR VHF/UHF IN B A METHOD B: Use a supplied antenna cable to connect the ATSC signal to the LCD TV's HDTV AIR terminal. Connect the AC power cord at the back of the TV and connect the power cord to wall outlet. TV CABLE HDTV AIR VHF/UHF IN This TV is equipped with a safety fuse. In the event of an electrical storm or power outage the safety fuse is designed to protect your TV. If your TV has no power, check the fuse by prying the cover off, following the illustration below. If the fuse is blown, visit your local hardware store and ask for a 4A 250V - 5x20mm Time Lag Fuse (Slow Blow) to replace the fuse. NOTE: Unplug the AC power cord from the back of your TV before removing the fuse. Firm Plastic Prying Tool (Using a metal tool may cause shock) Back of TV 4A 250V 5x20mm Fuse Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The POWER button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. Input TV(CABLE/AIR) HDTV (CABLE/AIR) VIDEO1 (SIDE) VIDEO2 (REAR) VIDEO3 (S-VIDEO) VIDEO4 (YPbPr1) VIDEO5 (YPbPr2) VIDEO6 (HDMI) COMPUTER (VGA) Press the Input button on the remote to display the Input List. Use an audio cable to connect the PC's audio output jacks to LCD TV's. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. Press the Input button on the remote to select COMPUTER. 25 Chapter 3 Using the LCD TV Connecting an Audio Receiver or a Dolby Digital 5. 1 Sound System For better sound quality, you may want to play the LCD TV audio through your stereo system. HDMI IN VGA IN AUD IO OUT YPbPr1 IN AUD IO AUD IO Y Pb Pr AUD IO STEREO DIGITAL OPTICAL TV CABLE HDTV AIR L R L R Y Pb Pr L AUD IO R L COAXIAL VHF/UHF IN VIDEO L R AUD IO VIDEO2 IN L R S-VIDEO AUD IO S-VIDEO IN L YPbPr2 IN R R AUDIO Cable B A Audio Receiv er Audio Amplifier Connecting to Audio Receiver: Use an audio cable to connect the audio receiver's audio LINE IN jacks to LCD TV's AUDIO OUT jacks. Connecting to Digital 5. 1 Sound System: METHOD A: Use an optical cable to connect the audio amplifier's OPTICAL IN jacks to LCD TV's OPTICAL OUT jacks. METHOD B: Use a coaxial cable to connect the audio amplifier's COAXIAL IN jacks to LCD TV's COAXIAL OUT jacks. Note: Above mentioned function is only available under HDTV (cable/air) mode. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. 26 Chapter 3 Using the LCD TV Chapter 3 USING THE FEATURES ENGLISH Using Picture-In-Picture The PIP/POP feature allows simultaneous viewing of video from two sources (TV, VCR, DVD etc). Only one source's audio is played at a time; the user may select which source's audio is heard. NOTE: Picture-in-Picture/Picture-on-Picture do not work when both picture sources are coming from component input (YPbPr). Press the PIP button once to enter picture in picture mode. Main Sub Press to toggle the audio source between the main window and the sub window. Press the OK button to change the position of the second window. SUB MAIN 1 3 5 2 4 Press to activate either the main or sub window, then press the Input button to display the Input List: Sub TV(CABLE/AIR) VIDEO1 (SIDE) VIDEO2 (REAR) VIDEO3 (S-VIDEO) VIDEO4 (YPbPr1) VIDEO5 (YPbPr2) COMPUTER (VGA) Press to change input source and press the OK button. 27 Chapter 3 Using the LCD TV Press the PIP button again to view images side by side. Main Sub Press to toggle the audio source between the main window and the sub window. Press the OK button to swap the pictures between the main and sub windows. Press to activate either the main or sub window, then press the Input button to display the Input List: Sub TV(CABLE/AIR) VIDEO1 (SIDE) VIDEO2 (REAR) VIDEO3 (S-VIDEO) VIDEO4 (YPbPr1) VIDEO5 (YPbPr2) COMPUTER (VGA) NOTE: Press to change input source and press the OK button. [. . . ] Keep this guide for future reference. A Quick Look at Programming a Device To control VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices, follow these steps. Before proceeding, find the codes for the devices you want to program in "Manufacturer's Codes" on the right side of this page and write them down or highlight them. NOTE: To program a DVD Player, TV/DVD Combo, TV/VCR/DVD Combo, portable DVD player, or mobile DVD player, use the DVD key. Turn on the device (for example, DVD player) and, if needed, load media (for example, a DVD). · NOTE: If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again. [. . . ]