User manual POLAROID LWT-19020

[. . . ] Table of Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Accessory List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 View of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect one end of the VGA cable to the VGA input jack on the jack panel of the unit and the other end to the PC VGA output. Connect one end of the audio cables to the PC audio input jack on the jack panel of the television and the other end to the PC audio output jack. Note: * X is the channel number. - 15 - System Setup Preparation 1. Press the SOURCE button to select TV mode and follow the procedures below. Image Setting Note: This item is only available when there is signal input. Press the MENU button once to enter the setup menu, as shown on the right: In the setup menu, press the button to select Image and then press the ENTER button to enter the item. Press the MENU button to return to the previous menu. Scheme Setup Press the button to select Scheme and press the ENTER button to enter. Press the button to select the desired item and press the ENTER button to confirm your selection. Press the MENU button to return to the previous menu. - 16 - System Setup Brightness Setup Press the button to select Brightness and press the button to adjust the value. Press the MENU button to return to the previous menu. Contrast Setup Press the button to select Contrast and press the button to adjust the value. Hue Setup Press the button to select Hue and press the button to adjust the value. Saturation Setup Press the button to select Saturation and press the button to adjust the value. Sharpness Setup Press the button to select Sharpness and press the button to adjust the value. Advanced Setup Press the button to select Advanced and press the ENTER button to enter. In the menu, press the button to select the desired item and then press the ENTER button to confirm. Note: This item is only available in Component and VGA modes. - 17 - System Setup Audio Setting Press the MENU button once to enter the setup menu. Press the button to select Audio and press the ENTER button to enter the menu shown on the right. In the Audio setup menu, press the button to select the desired item and press the ENTER button to enter. Press the MENU button to return to the previous menu. Volume Setup Press the button to select Volume and press the button to adjust the level. Bass Setup Press the button to select Bass and press the button to adjust the level. Treble Setup Press the button to select Treble and press the button to adjust the level. Balance Setup Press the button to select Balance and press the button to adjust the level. MTS Setup Press the button to select MTS and press the ENTER button to enter. [. . . ] Before the operations below, make sure that the television is unplugged and powered off. When wall mount the television, ensure that screws used between the wall mount and the back of the television are 18 mm (0. 70") or less in length. Stand Uninstall: 1. Note: To remove the stand, cover the screen with a soft cloth and place the LCD screen face down on a stable surface. Wall Mount Installation: Wall mount the TV with the supplied mounting screws through the mounting screw holes on the back of the TV and the optional mount on the wall. Note: Since the unit is rather heavy, be careful while doing the installation work. Stand Reinstall: 1. [. . . ]