User manual POLAROID PORTABLE DVD DOCKING STATION

[. . . ] The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus; 11. The mains socket-outlet shall be installed near the apparatus and the mains plug shall remain readily operable; 12. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. [. . . ] Three-digit number: press the first number, then input the second number in 2 seconds, and input the third number in the next 2 seconds. P-MODE button Press to change the picture modes: Bright, Soft or Nature. 16:9/4:3 button Press to change the screen aspect ratio between 16:9 and 4:3. 16. Note: When the portable DVD player is connected to the docking station, the mute button on the docking station remote control mutes the docking station only. If you want to turn off the volume of the portable DVD player, adjust the volume control on the portable DVD player to its minimum volume level. - 12 - Attaching & Detaching Portable DVD player Note: Do not connect the power cord until all other connections have been made. Attaching Portable DVD player to Docking Station Follow the steps below to attach the portable DVD player to the Docking Station. It is advised to attach the rechargeable battery to the portable DVD player before this connection. Step1: Center the player on the Docking Station and line up the 4 slots on the bottom of the player with the 4 fixing hooks on the Docking Station. Step2: Press the portable DVD player down gently with two hands and the fixing hooks will fix the portable DVD player on the Docking station from moving. Detaching Portable DVD player from Docking Station Step1: Slide the two release buttons toward the front of the Docking Station to unlock the fixing hooks. Step2: Remove the portable DVD player from Docking Station. System Connections - 13 - · · Do not connect the power cord until all other connections have been made. Ensure that you observe the color cord when connecting audio and video cables. Expand the Connections The following drawing shows a sample of expanding the connections of a portable DVD player with Docking Station: After connecting with external AV source by AV jacks, please turn on the power of the unit and press the SOURCE button on the front panel to shift to AV1 mode, or press the AV1 button on the remote control to shift the mode directly. If the AV source is from docking station, please press the SOURCE button on the front panel to shift to AV2 mode, or, press the AV2 button on the remote control to shift the mode directly. System Connections - 14 - Connecting to TV Signal Input Source The unit can be connected to a TV antenna to receive TV programs. Connections should be made as follows: After connecting the antenna, turn on the power of the Docking Station; press the SOURCE button on the front panel or the TV button on the remote control to switch to TV mode. - 15 - System Connections Connecting To the Power Adapter This unit is powered via the switching power adapter (supplied): 1. Connect the AC adapter to jack marked with "DC 12V IN" on the rear panel of the unit. 2. 3. Plug the other end of the power cord to the grounded electrical socket. Fine Tuning Use the buttons to select Fine Tuning, and then press the buttons to tune forward or backward from the current channel Auto Memory Use the buttons to select Auto Memory, press the button to enter auto memory mode: The auto memory will take a few minutes. The unit will search channels from the lowest channel to the highest channel in the standard channel list. When tuning operations are complete the unit will exit and store the channels by sequence in the memory. During tuning, press the button to exit the auto memory. - 18 - TV Setup Video Setup Press the MENU button and display the setup menu, press the buttons to select the Video setup sign (the third sign), the screen will display as below: Use the buttons to select, press the buttons to enter the select video mode. Press the buttons to highlight the video sign on the top of the menu, then press the button to enter the Clock menu; press the button to return to the TV setup menu. Press the MENU button to exit the setup. Clock Setup Press the MENU button and display the setup menu, press the buttons to select the clock sign, the screen will display as below: Use the buttons to select the item you want to set. Press the buttons to highlight the Clock sign on the top of the menu, then press the button to enter the LCD setup menu; press the button to return to the video setup menu. This function allows you to set the start time and end time of the desired signal source. No matter what mode the unit is in, it will automatically start the playback of the desired signal source. [. . . ] Make sure the portable DVD player is properly connected with the Docking Station. Make sure the portable DVD player is properly connected with the Docking Station. (See page 12) Make sure the TV cable is firmly connected with the Docking Station. (See page17) Make sure the video type of the AV signal source is PAL/SECAM. [. . . ]