User manual POLAROID SPRINTSCAN 45I QUICKSTART GUIDE

[. . . ] Once you have saved the final scanned image, you regain this disk space. 1 Unpack the Box Make sure you have all the following components. Contact your dealer if any is missing or damaged. a b c d e e f g h i j k l m SCSI cable (25-pin to 50-pin) Film carrier for 4x5 film Adapter for 120 film, 2¼ x 2¼ in. Adapter for single 35mm slide Adapter for 120 film, 2¼ x 2¾ in. Four-slide film carrier 35mm slide spacer (not shown) Two magnets for 120 film (not shown) The PolaColor Insight Software CD (not shown) containing: · PolaColor Insight software for Windows 95, 98, and NT · PolaColor Insight software for Power MAC and Power PC systems and an Adobe Photoshop plug-in · Online user's guide f g h i j a b c d Scanner Power cable This manual Pass-through terminator Warning: Nothing inside the scanner is user serviceable. [. . . ] Do not connect the scanner to the parallel connector on your computer. Doing so could damage the scanner or computer. I O 25 pins 50 pins Terminator c d e a b c Air intake SCSI address switch Power switch d e Power connector SCSI connectors (25, 50) Computer Scanner Note: The address is preset to 4. Other addresses typically available are 2, 5, and 6. 25 pins 50 pins 25 pins 50 pins Terminator You may need additional cables or adapters to connect the scanner. Your cable must have a 50-pin Centronics M or DB-25 M connector at one end for attachment to the scanner, and the cable should be as short as possible. To determine the connector you need for attachment to your SCSI adapter, refer to instructions with the adapter. Terminate the scanner and all other SCSI devices as shown in the appropriate diagram in the previous section. The last device in the SCSI chain must be terminated (or termination on), while all other devices must be unterminated (or termination off). Termination instructions for your other SCSI devices are provided with the devices. Computer Other SCSI device (unterminated) 50 pins 25 pins 50 pins Scanner 25 pins Computer Scanner Other SCSI device (terminated) English 8 English 9 5 Connect the Scanner to AC Power and Turn On 1 2 Turn on the scanner by pressing the power switch. Connect the power cord as shown. a b I I O 3 Check the lights. The yellow light blinks while the scanner initializes, remaining steady when the scanner is ready. Wait for the system to install the scanner driver and display the normal desktop. 4 I O 5 c d e a b c Air intake SCSI address switch Power switch d e Power connector SCSI connectors (25, 50) 6 Loading the Film Carriers The Four-Slide Film Carrier 1 With the text facing up and the hinge at the top, open the carrier flat as shown. 3 Close the carrier carefully. The 4x5 Carrier (for 4x5 film) 1 2 Place up to four mounted 35mm slides in the spaces provided. The emulsion side will face down. To unlock the carrier, squeeze the two halves of the carrier together at the bottom edge (near the locking knob) with one hand while turning the locking knob in either direction, until the slot in the knob points to UNLOCK. CK LO UN CK LO English 10 English 2 11 Open the carrier flat. Insert a 4x5 chrome or negative so that the left edge is against the positioning pins. Position the film so the image is right-reading and right-side up (emulsionside down). Note: The emulsion side is the dull side. The 120 Film Adapters (for 2¼ x 2¼ and 2¼ x 2¾ in. square images. Note: The frame of film must be cut from the film strip in order to be scanned. 3 Pins Orient the adapter so that the words THIS SIDE UP (on the adapter) face up, and the notches are at the left edge. Place the unmounted film over the opening, within the raised ridges of the adapter. Position the film so the image is rightreading and right-side up. 3 Close the carrier. Squeeze the carrier at the bottom edge and turn the knob to lock it. 3 4 Secure the film with the two magnets provided, on the top and bottom edges. Be sure the magnets are also within the raised ridges. CK LO CK LO UN The Single-35mm Carrier 1 5 Open the 4x5 carrier as described previously. Locate the single-35mm adapter. Note: You can use a negative, or a mounted or unmounted Place the adapter in the 4x5 carrier, sliding the notches into the pins on the left edge. The film and magnets should be face up, as shown. 2 slide. 3 Orient the adapter so the metal tabs face up, and the notches are at the left edge. Position the film so the image is rightreading and right-side up. 6 Close the carrier. Squeeze the carrier at the bottom edge and turn the knob to lock it. English 12 English 13 4 If the film is unmounted or the mount is thin, use the slide spacer provided. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient/relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]