User manual POLAROID SVGA 270

[. . . ] SVGA 270 LCD Projector User Guide Liquid Crystal Projector ENGLISH SVGA 270 USER'S MANUAL Thank you for purchasing this HITACHI liquid crystal projector. Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE: * The information in this manual is subject to change without notice. * The manufacturer assumes no responsibility for any errors that may appear in this manual * The reproduction, transmission or use of this documents or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT: * PS/2, VGA and XGA are registered trademark of International Business Machines Corporation. [. . . ] 6 Options Menu Item VOLUME MENU COLOR TIMER Description Volume adjustment: Reduce VOLUME Increase VOLUME Select menu background color: Select with the Operation start/stop: Press the or button. Select menu display language: Select with the and and buttons. LANGUAGE and buttons. AUTO OFF Operation start/stop: Press the or button. The system automatically enters the standby mode when a signal is not received for the set time. Wind Stop is selected the system does not enter the standby mode even if no signal is received. * When SYNC ON G is effective, it may not be displayed normally by an input signal. Remove a signal connector, and make it condition without a signal, and input a signal again in this case SYNC ON G after it is overridden. SYNC ON G 1-14 OPERATIONS (continued) The same adjustments and settings are available as with the Image and Options menus when the MENUO button is pressed during display of the `NO INPUT IS DETECTED ON ***' or `SYNC IS OUT OF RANGE ON ***' message while no signal is received. See Table 1. 7 below. VOLUME KEYSTONE BLANK MIRROR START UP MENU COLOR TIMER LANGUAGE AUTO OFF SYNC ON G 40 +1 Table 1. 7 No Signal Menu Item VOLUME KEYSTONE Description Increase VOLUME Volume adjustment: Reduce VOLUME Adjustment: Reduce size of bottom of image Reduce size of top of image BLANK Select blank screen color: Select color with the and buttons. * The image is cleared when the BLANK MODE is set with BLANK ON, or when there is no signal, and the entire screen is displayed in the selected color. Note that if TURN OFF is selected on the START UP the blank screen is displayed in blue when there is no signal. Select Mirror status: Select mirror status with and MIRROR buttons. START UP Operation start/stop: Press the or button. * Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal. Select menu background color: Select with the Operation start/stop: Press the or button. Setup initial timer value: Set 1~99 minutes with the Operation start/stop: Press the or button. buttons. MENU COLOR TIMER LANGUAGE AUTO OFF Operation start/stop: Press the or button. The system automatically enters the standby mode when a signal is not received for the set time. Wind Stop is selected the system does not enter the standby mode even if no signal is received. SYNC ON G invalid: Select TURN OFF with the button. * When SYNC ON G is effective, it may not be displayed normally by an input signal. Remove a signal connector, and make it condition without a signal, and input a signal again in this case SYNC ON G after it is overridden. SYNC ON G 1-15 ENGLISH No Signal Menu MAINTENANCE Lamps Electric shock High temperature Mechanical shock Contact your dealer before replacing the lamp. (Product name: Projector lamp /Model name: DT00301) Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. * For disposal of used lamp, treat according to the instruction of community authorities. * Since the lamp is made of glass, do not apply shock to it and do Lamp not scratch it. * If it is probable that the lamp has exploded (explosive sound is heard), disconnect the power plug from the power outlet and ask your dealer to replace lamp. [. . . ] Audio is present but * The brightness adjustment * Select BRIGHT with the MENU knob is rotated fully clockwise. Colors are pale and Color density and color color matching is matching are not correctly poor. Adjust the video. * Brightness and contrast are * Adjust the video. * Check and correct the setting of lamp cover and lamp. Video is blurred. The LAMP indicator Lamp failure. [. . . ]