User manual POLAROID TLA-02023BM

[. . . ] Need some help? This manual should help you understand your new product. If you have questions, call our toll-free number found on the insert with this icon: Or visit www. polaroid. com. TABLE OF CONTENTS IMPORTANT SAFETY AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] There are three modes: Low/Medium/High Low : The power consumption is no more than 10W in the POWER OFF status. Medium : The power consumption within the first hour is less than 35W and you can turn on TV around 3 seconds. After one hour, the power consumption is switched to around 5W and it takes 12-15 seconds to turn on the LCD TV. High : The LCD TV set can be turned immediately and the maximum power consumption would be less than 35W. ENGLISH 1. Press Exit button to exit all menu or press button to return to the previous screen. 15 Initial Setup When the system powers on for the first time, the initial auto installation is enabled. Use the buttons to select the language you prefer, and press OK button to continue. Time Zone Selection 2. Press the buttons to select on your Time Zone, and press OK button to continue. NOTE : It takes around 5 to 30 minutes to finish the Initial Setup process. The time taken for Initial Setup is varied according to the number of scanned channels. 16 Daylight Saving 3. Press buttons to set the Daylight Savings, and press OK button to continue. ENGLISH Input Source Selection 4. Press buttons to select the source for your TV signal, and press OK button to start scanning. If the user selects Antenna, the next setup wizard is presented. 17 When "Cable" Source is selected, please toggle Automatic, STD, IRC, or HRC. To have all channels completely scanned, please select STD, IRC or HRC. 5. After all the available channels are stored, the channel list will appear. 6. Press OK and start to watch TV. 18 Reset the features The user can reset all settings back to factory settings, including the channel map, all Program Info, Favorite channel lists, etc. If a PIN is set, the PIN entry dialog is displayed before the "Reset All" Settings dialog box, even if Locks are temporarily off. Press the buttons to select Settings and press / buttons to access the RESET ALL screen. 3. Press the to select "Reset" and OK buttons to reset all settings. 19 Changing Channels Using the Channel buttons When you press the CH + / - buttons, the TV changes channels in sequence. Using the Last button to select the previous channel To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Adjusting the Volume Using Volume Control Press the VOL + / ­ buttons to increase or decrease the volume. Using Mute At any time, you can turn off the sound using the Mute button. Press Mute again or VOL + / ­ buttons to return audio back to the previous volume level. 20 Switching Source 1. User can also press the SOURCE button repeatedly to choose the desired source. ENGLISH Viewing the Menus and On-Screen Displays You can use the control buttons on the right side of the TV or use the remote control to viewing the menus. [. . . ] If there is more than one code listed for device, enter the first one, and then try the POWER button. Repeat until you find a code that works. ENGLISH Cable Converters ABC Americast Bell & Howell Bell South Clearmaster ClearMax Coolmax Daeryung Digi Director Dumont Gehua General GoldStar Hamlin Hitachi Jerrold 00014 KNC LG Memorex Motorola MultiVision Pace Panasonic Panther 00008 00144 00000 00476, 00810, 00276, 01254, 01376 00012 01877, 00237 V 00000, 00008, 00107 00637 Trans PX Tristar TS 0 V2 Viewmaster 0 ision Vortex View Zenith 0 00276 00883 0003 00883 0883 00883 00883 0000, 00525, 00899 00003, 00008, 00014 00899 00014 00899 00883 00883 00883 01877, 00877, 00477, 00008 00637 00476 00637 00476 00476, 00810, 00276, 00003, 00014 00144 00009, 00273 T 00014 00476, 00810, 00276, 00003, 00012, Toshiba 00000 Paragon Philips Pioneer Pulsar Quasar RadioShack 0 Regal 0 Runco Samsung Scientific Atlanta Sony Starcom Supercable Supermax ocom Torx 00000 0 0317, 01305 0 1877, 00877, 00144, 00533 00000 00000 0883 0279, 00273 00000 00000, 00144 01877, 00877, 00477, 00008 01006 00003, 00014 00276 00883 0 0012 0 0003 53 Searching for a Device Code Satellite is found, If none of the codes listed in Device Codes listReceivers you can search for a set of commands that will work. Your Remote AlphaStar 00772 NEC will sample all the codes in its system to find one that will allow you to control your device. Chaparral 00216 Next Level 0 Crossdigital 01109 Panasonic As the Remote searches its library, it starts with the most popular device in the category and works00247, through to the end. [. . . ]