User manual POLAROID TLS-01911B

[. . . ] This equipment and recommended cart or stand should be handled with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart/stand to overturn. Removing the grounding pin will increase the risk of damaging the equipment. If you can not fit the plug into the electrical outlet, contact an electrician to install a grounding outlet. [. . . ] Connect the AC power cord to the back of the TV and then to the wall outlet. Insert the 2 supplied batteries in remote control. Step1 Slide the back cover up to open the battery compartment of the remote control. Step2 Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. Slide the cover back into place. Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner etc. ) on the remote, as it may suffer damage. Connect an external A/V device (refer to page16-23). 9 Chapter 1 Introducing the LCD TV Your LCD TV Front Side View and Controls Right Side View Front View Left Side View IR Infrared Receiver LED The LED light indicates when the LCD TV is activated. VOLUME + Adjusts the volume up and down. Selects the main-menu item and change values for items when in the OSD mode. HEADPHONE Connects to the external headphone for private listening. CHANNEL Scans up and down through channels. Selects sub-menu item when in the OSD mode. MENU Press once to display the OSD (on screen display), press again to turn the OSD off. INPUT Chooses from different input signal sources. Turns the LCD TV on and into standby mode. For this reason, a good quality outdoor antenna is strongly recommended. The following is a brief explanation of the type of connection that is provided with the various antenna systems. A 75-ohm system is generally a round cable (not included) with Ftype connector that can easily be attached to a terminal without tools. F-type connector 75-ohm coaxial cable (round) A 300-ohm system is a flat twin-lead cable (not included) that can be attached to a 75-ohm terminal through a 300-75-ohm adapter (not included). 300-ohm twin-lead cable (flat) 13 Chapter 2 Installing the LCD TV Use one of the following two diagrams when connecting an outdoor antenna. A. Combination VHF/UHF antenna VHF/UHF Antenna 300/75-ohm adapter (not included) VHF/UHF Antenna 300-ohm twinlead cable 75-ohm coaxial cable B. Separate VHF and/or UHF antennas UHF Antenna Combiner (not included) 300-ohm twinlead cable OUT IN VHF Antenna 75-ohm coaxial cable 300-ohm twinlead cable 14 Chapter 2 Installing the LCD TV Cable TV (CATV) Connection A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-ohm coaxial cable to the set, connect the 75ohm cable into the ANT. Since the signals of these premium pay channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/descrambler is necessary for normal viewing of scrambled channels. For more specific instructions on installing cable TV, consult your cable TV company. One possible method of connecting the coverter/descrambler provided by your cable TV company is shown in the diagram below. RF switch (not included) OUT A IN B ENGLISH 2 set signal splitter (not included) Cable TV Line VHF/UHF IN Cable TV converter/ descrambler (not included) The RF switch (not included) is required to provide two inputs (A and B). Setting the RF switch to position A allows viewing of all unscrambled channels by using the TV channel keys. Setting the RF switch to position B allows viewing of all scrambled channels via the converter/descrambler by using the converter channel keys. 15 Chapter 2 Installing the LCD TV Use a supplied antenna cable to connect to the LCD TV's TV UHF/VHF terminal. VHF/UHF IN Connect the AC power cord at the back of the TV and connect the power cord to wall outlet. AC IN Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. Press the TV button repeatedly on the remote to enter TV mode. 16 Chapter 2 Installing the LCD TV Connecting an A/V Device with Composite Connector Rear of TV COAXIAL ENGLISH VIDEO OUT A/V Cable L R DVD PLAYER Use a composite cable to connect the external A/V device's composite video/audio jacks to the LCD TV's VIDEO/AUDIO IN jacks. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To view the A/V device's with component input, press the SOURCE button on the remote to select AV. 17 Chapter 2 Installing the LCD TV Connecting an A/V Device with S-Video Connector Rear of TV COAXIAL S-VIDEO OUT S-VIDEO Cable AUDIO Cable L R DVD PLAYER Use an audio cable to connect the external A/V device's audio output jacks to the LCD TV's audio inputs. Use a S-Video cable to connect the external A/V device's S-Video output jack to the LCD TV's S-Video IN input jack. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. [. . . ] Press the OK button to automatically adjust the display settings to optimize performance based on the VGA mode. Controls the width of the picture based on the VGA mode. 33 Troubleshooting TROUBLESHOOTING Before consulting service personnel, check the following chart for a possible cause of the trouble and for a possible solution. TV will not turn on Make sure the power cord is plugged in, then press the The batteries in the remote control may be exhausted. button on the remote. No picture, no sound Check the interface cable between TV and antenna/cable TV. Press the button on the remote. Press the SOURCE button on the remoterepeatedly to select the connected video sources. Poor picture, sound OK Check the interface cable between TV and antenna/cable TV. [. . . ]