User manual POLAROID TLU 19

[. . . ] All rights reserved. "Polaroid" and "Polaroid and Pixel" are trademarks of Polaroid Corporation, Waltham, MA, USA. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions. For service, support and warranty information, visit www. polaroid. com. This product contains electrical or electronic materials. The presence of these materials may, if not disposed of properly, have potential adverse effects on the environment and human health. [. . . ] For wall mounting the stand socket attached to the back of the TV should be detached. Using a Phillips screwdriver remove the screw which is inside the stand socket. The stand socket section should then slide off the locator rod connected to the TV. To attach this LCD TV to a wall a standard 100x100 VESA mounting bracket is required. 7 Chapter 1 Introducing the LCD TV How to setup the TV Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV's ANT. Connect the AC power cord at the back of the TV and connect the power cord to wall outlet. Insert the 2 batteries supplied in remote control. Step1 Slide the back cover up to open the battery compartment of the remote control. Step2 Insert two AAA size batteries. Cycles through the TV sound options (NICAN) : MONO/DUAL/STEREO Mutes and restores your LCD TV sound. 1 2 SCALE 3 4 4 5 SCALE Cycles through Wide mode settings : 3 6 7 In TV/AV/S-VIDEO/SCART mode: NORMAL /FULL/ZOOM1/ZOOM2 In YPbPr/HDM mode, only 480i and 576i mode can be adjusted : NORMAL /FULL/ZOOM1/ZOOM2 8 In VGA/DVI mode, "Scale" function is not available 5 12 VOL. INPUT CH. 9 10 11 ENT Turns on and off the Teletext function. 6 7 SLEEP DISPLAY Cycles through the LCD TV sleep time. Pressing once displays a variety of information such as the current channel and the input source. Following selection, pressing ENT activates the channel, or channel activates automatically in 3 seconds. Scans up and down the channels. 8 0-9/ENT S. MODE P. MODE 9 JUMP 10 TV 11 VOL. +12 CH. +- 11 Chapter 2 Installing the LCD TV 13 INPUT Pressing INPUT displays the source list, use to select the video equipment connected to the video inputs of your LCD TV TV AV S-VIDEO YPbPr SCART HDMI VGA SCALE ENT 14 15 EXIT MENU Exits the OSD menu. Selects picture mode: Vivid/Movie/ Game/Sport/User Press the appropriate colour to direct access the colour page. Reveals hidden information such as the answer to a quiz in TELETEXT mode. Displays the top, bottom or all of page, to easily read in TELETEXT mode. VOL. INPUT CH. 16 OK 13 14 16 S. MODE P. MODE 15 17 S. MODE 18 18 19 19 20 P. MODE 17 20 22 21 21 23 22 23 Effective range: The remote can control the LCD TV from up to 5m away, if pointed directly at the receiver. 12 Chapter 2 Installing the LCD TV Chapter 2 Installing the LCD TV ENGLISH Refer to the owner's manual of any external equipment to be connected. When connecting any external equipment, do not connect any AC power cords to wall outlets until all other connections are completed. Connecting a TV Cable or an Antenna Antenna Connection The antenna requirements for good color TV reception are more important than those for a black & white TV reception. For this reason, a good quality outdoor antenna is strongly recommended. The following is a brief explanation of the type of connection that is provided with the various antenna systems. A 75-ohm system is generally a round cable (not included) with IECtype connector that can easily be attached to a terminal without tools. IEC-type connector 75-ohm coaxial cable (round) A 300-ohm system is a flat twin-lead cable (not included) that can be attached to a 75-ohm terminal through a 300-75-ohm adapter (not included). 300-ohm twin-lead cable (flat) 13 Chapter 2 Installing the LCD TV Use one of the following two diagrams when connecting an outdoor antenna. Combination VHF/UHF antenna VHF/UHF Antenna 300/75-ohm adapter (not included) VHF/UHF Antenna 300-ohm twinlead cable 75-ohm coaxial cable B. Separate VHF and/or UHF antennas UHF Antenna Combiner 300-ohm twin(not included) lead cable OUT I N 75-ohm coaxial cable 300-ohm twinlead cable VHF Antenna 14 Chapter 2 Installing the LCD TV Cable TV (CATV) Connection A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-ohm coaxial cable to the set, connect the 75ohm cable into the ANT. Since the signals of these premium pay channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. ENGLISH This converter/descrambler is necessary for normal viewing of scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used. [. . . ] Controls the overall brightness of the picture. Brightness Tint Controls the difference between the green and red regions of the picture. 29 Chapter 3 Using the LCD TV Saturation Controls the color intensity. Sharpness Increase this setting to see crisp edges in the picture; decrease it for soft edges. Selects through Wide mode settings : Scale In TV/AV/S-VIDEO/SCART mode: NORMAL /FULL/ZOOM1/ ZOOM2 In YPbPr/HDM mode, only 480i and 576i mode can be adjusted : NORMAL /FULL/ZOOM1/ZOOM2 In VGA/DVI mode, "Scale" function is not available Color Temp Adjusts color components independently to achieve a warm or cool effect: Cool/Warm/User Warm: Cool: User: Increases red tint Increases blue tint Allows the user to adjust red, green and blue color component levels independently. Picture Color Temp R-Gain G-Gain B-Gain User 50 50 50 30 Chapter 3 Using the LCD TV Customizing the AUDIO Settings ENGLISH Press the button to turn the LCD TV on. Press the MENU button on the remote control to display the Main menu, and use the buttons to select the AUDIO. Use the buttons to highlight an individual AUDIO option, use the buttons to change the setting, and press the MENU to exit the menu If the signal source is AV/S-VIDEO/YPbPr/HDMI/ SCART, the AUDIO Menu appears as: If the signal source is TV, the AUDIO Menu appears as: Audio Setup Sound Mode Volume Bass Treble Balance Mute User 50 50 50 50 On Sound Mode Volume Bass Treble Balance Mute Audio Setup User 50 50 50 50 On If the signal source is VGA, the AUDIO Menu appears as: Audio Setup Sound Mode Volume Bass Treble Balance Mute User 50 50 50 50 On The AUDIO Setup menu includes the following options: Sound Mode Allows selection of an audio-enhancement technique from among the following options: Live/Rock/POP/User. [. . . ]