User manual POLAROID TLX-04243B

[. . . ] 42" FULL HD LCD TV Your TV may look different from the one pictured. Questions?Need some help? This manual should help you understand your new product. If you still have questions, call our help line found on the insert with this icon: Or visit www. polaroid. com/support. Digital Television Transition Notice: This device contains a digital television tuner, so it should receive digital over the air TV programming, with a suitable antenna, after the end of full-power analog TV broadcasting in the United States on February 17, 2009. Some older television receivers, if they rely on a TV antenna, will need a TV Converter to receive over the air digital programming, but should continue to work as before for other purposes (e. g. , for watching low-power TV stations still broadcasting in analog, watching pre-recorded movies, or playing video games). When a Converter is used with an older television receiver, a signal splitter might be necessary to continue to receive low-power analog broadcasts via an antenna. [. . . ] (Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown, consult your cable TV company. ) For more specific instructions on installing cable TV, consult your cable TV company. One possible method of connecting the converter/descrambler provided by your cable TV company is shown in the diagram below. ENGLISH RF switch (not included) OUT A IN B 2 set signal splitter (not included) Cable TV Line VHF/UHF IN Cable TV converter/ descrambler (not included) The RF switch (not included) is required to provide two inputs (A and B). Setting the RF switch to position A allows viewing of all unscrambled channels by using the TV channel keys. Setting the RF switch to position B allows viewing of all scrambled channels via the converter/descrambler by using the converter channel keys. 19 Chapter 2 Installing the LCD TV Use a supplied antenna cable to connect the TV signal to the LCD TV's TV CABLE terminal. HDTV/TV Air/CABLE VHF/UHF IN Connect the AC power cord at the back of the TV and connect the power cord to wall outlet. HDTV/TV Air/CABLE VHF/UHF IN This TV is equipped with a safety fuse. In the event of an electrical storm or power outage the safety fuse is designed to protect your TV. If your TV has no power, check the fuse by prying the cover off, following the illustration below. If the fuse is blown, visit your local hardware store and ask for a 4A 250V - 5x20mm Time Lag Fuse (Slow Blow) to replace the fuse. Firm Plastic Prying Tool (Using a metal tool may cause shock) Back of TV 4A 250V 5x20mm Fuse BE SURE TO UNPLUG AC POWER CORD BEFORE REMOVING THE FUSE. Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The POWER button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. 20 Chapter 2 Installing the LCD TV Press the button on the remote to turn on the LCD TV. ENGLISH Main TV(CABLE/AIR) VIDEO1 (SIDE) VIDEO2 (REAR) VIDEO3 (S-VIDEO) VIDEO4 (YPbPr1) VIDEO5 (YPbPr2) VIDEO6 (HDMI1) VIDEO7 (HDMI2) COMPUTER(VGA) Press the INPUT button on the remote to display the Input List. Use the buttons to select TV and press the OK button. Channel Scan Tuner Mode Channel Skip Favorite List Time Zone Cable Eastern Time TV Select Exit Press the MENU button on the remote control to display the Main menu, and use the buttons to select the TV. Status: Scanning. . . . . Analog Channels: 25 Digital Channels: 0 Cable 47% The Channel Scanning will create a list of receivable channels for the current input (antenna or cable). You will be required to run Channel Scanning for each RF input to create a list of available channels from both inputs. Press the OK button to display the received channel list, then press to select a channel. Or, use the (INPUT button) with 0-9 buttons to select digital channel( for example 9. 1) Channel List 5-2 RF5-2 9-1 KQED-HD 9-2 KOED-SD 8 CCT 12 13 15 The digital main channel might include many subchannels (for example 9-1, 92. . ) that are showing program at the same time. 21 Chapter 2 Installing the LCD TV Connecting a VCR Rear of TV AUDIO Cable S-VIDEO Cable AV Cable A B METHOD A: Use a composite cable to connect the VCR's composite video/audio jacks to the LCD TV's VIDEO2 IN jacks. METHOD B: Use an audio cable to connect the VCR's audio output jacks to the LCD TV's audio inputs. Use a S-Video cable to connect the VCR's s-video output jack to the LCD TV's S-VIDEO IN input jack. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To watch a videotape, press the INPUT button on the remote to select VIDEO2( METHOD A), or VIDEO3 (METHOD B). Turn on your VCR and follow the instructions in your VCR's manual. 22 Chapter 2 Installing the LCD TV Connecting a Video Camera or Game console Rear of TV ENGLISH Right Side VIDEO L R VIDEO1 IN or AUDIO Cable S-VIDEO Cable B AV Cable GAME CONSOLE A METHOD A: Use a composite cable to connect the video camera's or game console's composite video/audio jacks to the LCD TV's VIDEO2 IN jacks or VIDEO1 IN jacks. METHOD B: Use an audio cable to connect the video camera's or game console's audio output jacks to the LCD TV's audio inputs. [. . . ] If you cannot find a code that works, see "Searching for Your Code". Repeat steps 1­5 for the other devices you want to control. For future reference, write down each working device code below: AUX Code: CBL Code: CD Code: DVD Code: SAT Code: TNR Code: VCR Code: Press SET UP to save and exit. 50 Programming Your Remote Control Searching for your Code If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code: ENGLISH ENGLISH ENGLISH Press a device key once. Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). The remote sends IR codes from its library to the selected device, starting with the most popular code first. [. . . ]