User manual PROCOLOR DYNA SCREEN RF DATASHEET

[. . . ] Extension cords do not guarantee the required safety of the appliance (e. g. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. [. . . ] The marks indicate the approximate fill level in ml when the door is open in a horizontal position. 33 Use Turning on ^ Open the water supply, if closed. The last program selected will appear in the display and the appropriate indicator light will come on. After a short while, the estimated program duration for the program selected will appear in the display. Starting a program ^ Start the program by closing the door. the water softening) could be interrupted. Selecting a program Choose your program according to the type of load and soiling. Additional options can now be selected, if desired (see "Additional Options"). 34 Program Guide Program guide When to use Pre-rinse 1 2 Program sequence Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. X X X X X Normal as Program for completely required washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. For temperature sensitive glassware and lightly soiled dishware, use 50% detergent recommended. X as requi red X X X X China & Crystal X as required X X SaniWash X X X X Extra Quiet X X X X Rinse & Hold Usage: Electrical - 0. 01 - 1. 30 kWh Water - 1. 1 - 5 gal (4 - 19 l) 35 Use Time display Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time is shown in the time display. Symbols will appear to indicate the current stage of the program: 1 8 % ( G O Standby A few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy. The display and the indicators are turned off and only the K indicator light flashes slowly. If you do not turn the dishwasher off after the program ends, it will turn completely off after a few minutes in standby mode (see "Settings - Optimize standby"). Once set, the function will remain active for the program selected until the setting is changed. Turbo The "Turbo" function can be used to reduce the program run-times, in programs in which the option is available. The Turbo indicator light will come on if the function is available for the program which has been selected. Once selected, the function will remain active for all programs until the setting is changed. 39 Additional options Delay start The start time of a program can be delayed. When using the "Delay start" function, make sure that the detergent compartment is dry before adding detergent. Otherwise the detergent could stick together and not completely rinse out. If you press and hold the , button, the time will automatically count up to 24 h. If, after you have set the delay start time, you do not close the door within a few seconds, the display will revert to showing the program duration. The display shows the remaining time, the , indicator light goes out, and the indicator light of the selected program comes on. 40 Additional options Starting a program before the Delay start has elapsed: A program can be started before the Delay start time has elapsed. The optical control lights to confirm that a program has started. 41 Settings menu The "Settings" menu allows you to change standard settings Opening the "Settings" menu ^ Press the K button to turn the dishwasher off. ^ Turn the dishwasher on with the K button and hold the "Program" button down for at least 4 seconds. The first option of the Settings menu will appear in the display and all the indicator lights will come on. [. . . ] The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. , Improper connection of the equipment grounding conductor can result in electric shock. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 67 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , Prior to making a hardwire , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. [. . . ]