User manual REMINGTON MS2-290

[. . . ] Do not use this appliance with a damaged or broken screen or cutters, as injury may occur. DANGER To reduce the risk of electric shock: Do not reach for an appliance that has fallen into water. Do not place or store this appliance where it can fall or be pulled into a tub or sink while it is plugged in. Except when charging, always unplug this appliance from the electrical outlet immediately after using. Do not use an extension cord or a voltage converter with this appliance. SAVE THESE INSTRUCTIONS Contents English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3 2 CS27659_MS2_series_IB 9/1/05 11:10 AM Page 4 Product Features Titanium MICROSCREENTM 300 & 500 Congratulations on your purchase of a premium Remington® shaver. [. . . ] This allows the shaver to work the way it was designed for the closest shave and minimum wear. Avoid holding the shaver at an angle so only one screen touches the skin at a time. This encourages your whiskers to stand out, making it easier for them to enter the cutting chamber. Pressing only flattens your whiskers, making it harder for them to enter the cutting chamber. Remington® Pre-Shave Powder Stick (SP-5) can help maximize your shaver's performance. Its absorbs moisture and facial oils, helping set up the hairs so they enter the cutting chamber more easily. It makes shaving quicker and more comfortable. Removing the Headguard Before operating your shaver, remove the headguard, which protects the screen and cutter assembly. It is important to remove the headguard correctly to avoid damaging the clips that hold it to the shaver. Always keep the protective head guard on the shaver head and keep the trimmer in the OFF position when the shaver is not in use. 6 7 CS27659_MS2_series_IB 9/1/05 11:10 AM Page 8 Cleaning & Maintenance Cleaning Your Shaver Remington® recommends cleaning your shaver after every use for optimal performance. Remove the head assembly by squeezing on both release buttons and pulling up from the body of the shaver. Instead, blow the shavings out or rinse the screens under cold or warm water. Cutters and trimmerUse the cleaning brush to sweep any loose hairs from the cutters and trimmers, or rinse/dunk them in cold or warm water. After cleaning, return the foils and head assembly to their original position on the shaver. If the shaver was rinsed with water hold it facing downward into the sink, and turn it on for a few seconds to dispel additional water. Do NOT use a hairdryer or heater to dry the shaver. Screens and Cutters To assure smooth, efficient performance, it is important to clean your shaver. Remove the head assembly by squeezing on both release buttons an pulling up from the body of the shaver. Remove the head assembly by squeezing on both release buttons and pulling up from the body of the shaver. Remington® Shaver Saver® Lubricant (SP-4) lubricates and cleans your shaver's cutters and head assembly. A quick spray after each shave keeps your shaver operating at peak performance. Cleaning Cautions Shaver can be placed under running water for cleaning only. Do not use an aggressive cleansing agent as this may destroy the shaver coatings. Do not remove or replace the head assembly while shaver is running as it may cause damage to the unit's screens or cutters. [. . . ] ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE LIMITED IN DURATION TO TWO YEARS FROM DATE OF ORIGINAL PURCHASE. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province. Some states do not allow the exclusion or limitation of incidental, special or consequential damages. Spectrum Brands, Inc. Money-back Offer If within 30 days after you have purchased your Remington® branded product, you are not satisfied and would like a refund, return it with the sales slip indicating purchase price and date of purchase to the retailer from whom it was purchased. [. . . ]