User manual REMINGTON MS2-300

[. . . ] Your new Remington® MicroScreen® 2 is the only one with Total Closeness TechnologyTM(TCT®). TCT ® combines two super-flexing screens with a specially designed Intercept Trimmer TM that shaves even the most difficult parts of your face, including your neck, incredibly close. The Intercept TrimmerTM works in tandem with the screens to first cut the difficult longer hairs that then allows the screens to shave the shorter hairs even closer. So allow about three weeks to develop an effective shaving style and for your beard to adjust to the new shaver. The adaptation period may take a little longer if your skin is sensitive, or if you alternate between shaving methods. [. . . ] s Do not push downward on the ends of the cutters, as you may bend the cutter, reducing its ability to operate smoothly. s Do not remove cutters from the plastic pieces to which they are attached, as you may damage the assembly. Replacing Screens and Cutters Because they are subject to daily use, the cutters and foils of your Remington® MicroScreen® 2 TCT® Shaver will wear and eventually require replacement to maintain a close, comfortable shave. Depending on your shaving technique and habits, the foils will usually last six months; the cutters, one year. Some signs that your foils and cutters need replacing are: s Irritation. As foils get worn, you may notice that your skin feels more sensitive after a shave, particularly when you apply aftershave. As cutters wear, your shave may not feel as close and you may feel your shaver is pulling at your whiskers. To prevent inadvertent damage to the Screen and Cutter Assembly, do not attempt to remove them unless you are replacing them. To remove the old screens and cutters follow the instructions that come with the screen and cutter replacement package. It's always a good idea to replace the screens when you replace the cutters. Removing the headguard Before operating your MicroScreen ®2 TCT® Shaver, remove the headguard, which protects the screen and cutter assembly. It is important to remove the headguard correctly to avoid damaging the clips that hold it firmly to the shaver. s Pull the headguard away from the shaver. Charging Prior to using your shaver for the first time, put it on charge for 24 hours. To charge your shaver: s Slide the power button downward to the "Off " position. s Connect the AC power cord to the shaver and then to the electric outlet. s Your shaver cannot be overcharged, so you can leave it plugged in and charging between shaves. s The MS2-300/400 on the other hand, comes with a special feature that allows you to shave while your shaver is plugged in for recharging. Your shaver will not be recharging while you are shaving, so after shaving, turn off the shaver by sliding the power button downward, and leave it plugged in so it can be recharged. s The MS2-300/400 will provide a week's worth of shaving after a one hour charge or a single shave after five minutes of charging. Model MS2-400 The green indicator lights show that the shaver is charging. The lights will start to flash as the battery charge rate slows. This shaver features a lighted fuel gauge that displays the amount of charge remaining. When only 20% of the charge remains, the red "low battery" warning light illuminates. This indicates approximately 5 to 6 minutes of shaving time left when first illuminated. Model MS2-300 The green indicator light shows that the shaver is charging. This light will start to flash as the battery charge rate slows. [. . . ] Authorized Service Center Dealers may be found in the yellow pages of your directory. If you wish, you may mail the product, postpaid, to Remington Products Company, L. L. C. , 60 Main Street, Bridgeport, CT 06604 Attention:Service Department. U. S. Warranty Service In the United States, service is provided by our Company-owned Service Centers and over 300 Authorized Service Dealers. For the address of your nearest Authorized Service Dealer, please consult the Yellow Pages under "Shaver - Electric - Repair. " If you wish, you may mail the product, postpaid, to Remington Products Company, L. L. C. , 60 Main Street, Bridgeport, CT 06604, Attention: Service Department. International Warranty Service Service under the Remington warranty can be obtained outside the United States by Remington-Authorized Distributors and Service Dealers. [. . . ]