User manual REMINGTON S-8000I WIDE PLATE STRAIGHTENER

[. . . ] As a safety feature, this plug will fit in a polarized outlet only one way. Do not attempt to defeat this safety feature. READ ALL INSTRUCTIONS BEFORE USING. KEEP AWAY FROM WATER. DANGER To reduce the risk of electric shock: s Do not reach for an appliance that has fallen into water. s Do not place or store this appli ance where it can fall or be pulled into a tub or sink. [. . . ] (A) Steam vents and channels (B) plus Ceramic coating (C) Ionic conditioning (D) LCD display (E) Steam icon (F) Numerical heat setting indicator (G) Graphic heat setting indicator (H) +/- Temperature controls (I) ON/OFF button (J) Swivel cord (K) Closing lock (B) Automatic worldwide voltage This appliance contains a special electronic circuit that automatically converts it for worldwide usage ­ from 100 to 240 volts AC, 50 to 60 Hz. Just plug it into the local outlet and use it as normal; the styler will automatically adjust to the local current. (You may need an adapter to allow the plug to fit into the local outlets, however. ) ** * * (A) ** * * (C) ** 3X Protection: 3X Protection products from Remington ® have an exclusive Teflon® plus Ceramic coating and Ions for the ultimate defense against damage for superior shine. Teflon® coating: Non-stick Teflon® coating glides through any type of hair, preventing static, stickiness, and build-up of mousses, gels, and hair sprays for smooth, shiny results ­ every time. 2. Ceramic coating: Ceramic protects against damaging hot spots with high, even heat to lock in moisture and create long-lasting styles. 3. Ionic conditioning: Negative ions are created, neutralizing positive ions to reduce static and the frizzies, leaving your hair looking shin y and healthy. (J) (D) (H) (I) (E) (F) (G) (K) 4 5 How to Use Heat Settings Take extra care when using a professional styler. To prevent hair damage, make sure to use the correct temperature setting for your hair type. Usage Tips Straightening Your Hair 1. Avoid rubbing hair with a towel, as this creates split ends and frizziness. Press and hold theON/OFFbutton until the unit turns on and the LCD lights up. Adjust the temperature using the +/- buttons. The bars on the LCD will flash while the unit heats up, then glow steadily when it has reached the selected temperature. The styler will beep three times when it is ready for use. Divide hair into manageable sections and clip the upper layers on top of your head and out of the way. Test the styler on a small section of hair, then adjust the temperature up or down before styling the rest of your hair. NOTE: s If you find that you need a higher setting while straightening your hair, simply adjust the temperature by pressing the "+" button. s While straightening your hair, if you find that you need a lower setting, adjust the temperature by pressing the "-" button. Because the unit is already hot, it may take a few minutes to cool off. It will beep when it cools to the lower temperature. Take a small section of hair and comb through it with a fine-toothed comb. Hold the straightener with the LCD and steam vents facing away from your scalp. Starting at the roots, clamp hair firmly between the plates and run the styler down the entire hair strand, from root to tip, in one smooth stroke. Do not hold it in one area for a long period of time or damage to hair may occur. To speed up drying at the roots, you may wish to run the styler over the first few inches of hair nearest the root several times. [. . . ] This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province. Some states do not allow the exclusion or limitation of incidental, special or consequential damages. Or visit www. remington-products. com Remington and wet2straight are trademarks of Rayovac Corporation. Teflon is a registered trademark of E. I. du Pont de Nemours Company and is used under license by Rayovac Corporation. Patent Pending ©2004 R. C. Error Messages rE Your straightener will display an "rE"message if it has a recoverable error or malfunction. If this happens, turn the unit off, unplug it, and allow it to cool for 10 ­15 minutes. Then plug it in and turn it on again. [. . . ]