User manual REMINGTON TITANIUM

[. . . ] O This appliance should be charged by approved safety isolating adaptors PA-3215E (for HC5400 EU version) or PA-3215U (for HC5400 UK version) with the output capacity of 3. 2V dc; 1500mA; and should be charged by approved safety isolating adaptors PA-4515E (for HC5600, HC5800 EU version) or PA-4515U (for HC5600, HC5800 UK version) with the output capacity of 4. , QUICK CHARGE (HC5600 & HC5800) Quick charge time Run time 10 minutes 5 minutes 30 minutes 15 minutes 1 hour 30 minutes 2 hours 40 minutes , CHARGING VIA CHARGING STAND (HC5800) • Ensure the product is switched off. € Connect the charging adaptor to the charging stand and then to the mains. [. . . ] € Slide it onto and along the clipper blade until the front of the comb firmly sits against the clipper blade. , TO REMOVE THE COMB • Holding the clipper with the blades facing away from you, firmly push the comb upward and away from the blades. , INSTRUCTIONS FOR CUTTING HAIR For even cutting, allow the comb attachment/blade to cut its way through the hair. If you are cutting for the first time, start with the maximum comb attachment. € Slowly lift the clipper, working upwards and outwards through the hair, trimming just a little at a time. , STEP 2 – Back of the head • With the comb set at 12mm or 18mm, cut the hair at the back of the head. , STEP 3 – Side of the head • Set the comb to 3mm or 6mm, trim sideburns. Then change the setting to 9mm and continue to cut the top of the head. , STEP 4 – Top of the head • Use the longer length comb attachment and set it to 24mm or 27mm then cut hair on top of the head against the direction in which the hair normally grows. € For longer hair on top, use the longer length comb attachment (24 – 42mm) to achieve the desired style. , STEP 5 – The finishing touches • Use the clipper without an attachment comb for close trimming around the base and sides of the neck. It is not necessary to remove the small moving blade from the unit. € If the moving blade has been removed this can be re-fitted by slotting the coated blade holder over the pin in the centre of the interior product head. The groove on the coated blade, just below the teeth, rests on a metal plate at the opposite side to the screw holes. The fixed blade is fitted with the raised profile pointing outwards and fixed with the 2 screws. € Note that if the blades are not correctly aligned then cutting efficiency will be impaired. € Place a few drops of cutter or sewing machine oil onto the blades. , CLEANING CAUTIONS • Ensure the appliance is switched off and unplug from the main outlet before cleaning. € Only the attachment guide combs and trimmer blade may be removed from the product for cleaning. € Cleaning should be done with a soft brush, such as the brush supplied with the product. € Do not use harsh or corrosive cleaners on the units or their blades. 8 ENGLISH GB BATTERY REMOVAL • The battery must be removed from the appliance before it is scrapped. [. . . ] Dette apparat skal oplades med godkendte sikkerhedsisolerede adaptere PA-3215E (til HC5400 EU-version) eller PA-3215U (til HC5400 engelsk version) med en effektiv ydeevne på 3, 2V dc; 1500mA; Og skal oplades med godkendte sikkerhedsisolerede adaptere PA-4515E (til HC5600, HC5800 EU-version) eller PA-4515U (til HC5600, HC5800 engelsk version) med en effektiv ydeevne på 4, 5V dc; 1500mA; AE 51 HR SL GR RO TR RU HUN PL CZ SK P FIN S DK I E F NL D DANSK , HURTIG OPLADNING (HC5600 & HC5800) Tid for hurtig opladning Brugstid 10 minutter 5 minutter 30 minutter 15 minutter 1 time 30 minutter 2 timer 40 minutter , OPLADNING VIA OPLADNINGSSTANDEN (HC5800) • Sørg for at produktet er slukket. • Sæt opladningsadapteren i opladningsstanden og derefter i stikkontakten. € Lad apparatet oplade helt i 16 timer for HC5400 og 4-5 timer for HC5600 og HC5800. , LEDNINGSFRI BRUG • Når enheden er tændt og fuldt opladet, kan den anvendes uden ledning i op til 60 minutter for HC5400 og op til 120 minutter for HC5600 & HC5800. [. . . ]