User manual ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER

[. . . ] AnoGotcha Stand with Topper Clips TM Instruction Sheet Parts Read this instruction sheet carefully before assembly. Make sure all parts are accounted for before discarding any packaging materials. If you experience any problems with the assembly, please call Rose Displays at 1-800-631-9707. AnoGotcha Shell 12AT300 T-Gotcha 12GT100 9" round base 97-0302 vertical poles 97-0301 ball knobs & threaded rods 97-0303 97-0304 shaped end caps 97-0305 Topper Clips 06-6100 These are all the parts required to assemble 1 AnoGotcha Stand. Important terms: Topper Clip top AnoGotcha holder vertical post ball knobs bottom AnoGotcha holder Finished look. 9" round base AnoGotcha is a registered trademark of Rose Displays, Ltd. [. . . ] Tighten securely. ball knobs top AnoGotcha holder 9" round base Slide threaded rod through the top hole of one vertical pole and then through top channel of one AnoGotcha holder. Screw ball knob tightly onto threaded rod. vertical pole Your stand should now look like this. AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSAnoGotchaStandTopper 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 5 · Choose the height slot that matches the length of your graphic. · Slide one threaded rod with ball knob (created in step 1) through appropriate hole in one vertical pole (created in step 2) and through bottom channel of one AnoGotcha holder (created in step 3). · Slide threaded rod through corresponding slot of second vertical pole. Note: Make sure the hinge on the bottom T-Gotcha faces up and in the same direction as the hinge on the T-Gotcha at the top of the stand. Note: Ball knob must be kept loose until graphic is inserted. 28" 28" assembly continued Attach bottom AnoGotcha holder to vertical poles. 48" 60" Bottom AnoGotcha must be attached at slot that matches the length of your graphic. T-Gotcha hinge must face up and in the same direction as T-Gotcha on the top. 48" 60" Slide threaded rod through height slot that matches the length of your graphic and through bottom channel of remaining AnoGotcha holder. AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSAnoGotchaStandTopper Slide threaded rod through matching hole on opposite vertical pole. Attach ball knob, but do not tighten. Leave loose until graphic is inserted. 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 6 · Open top AnoGotcha holder and insert top edge of your graphic until it reaches the top of the holder. · Open the bottom AnoGotcha holder and insert bottom edge of your graphic until it reaches the bottom of the holder. Snap shut bottom holder. assembly continued Insert your graphic into AnoGotcha Stand. Poster inserted into top AnoGotcha holder. [. . . ] Be sure to push graphic completely into clip. Finished Look If you have any questions about your AnoGotcha Stand assembly, please call Rose Displays at 1-800-631-9707 and we will assist you. The AnoGotcha Stand is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSAnoGotchaStandTopper 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com [. . . ]