User manual ROTEL RA-913

[. . . ] Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. Cleaning ­ Unplug this product from the wall outlet before cleaning. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. [. . . ] Control range: 0 to 100% 72 En SOUND FIELD PROGRAMS Sound field parameter Features Pro Logic IIx Music and Pro Logic II Music panorama. Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. Choices: OFF, ON Pro Logic IIx Music and Pro Logic II Music dimension. Control range: ­3 (towards the rear) to +3 (towards the front) Initial setting: STD (standard) PRO LOGIC IIx Music PRO LOGIC II Music PANORAMA PRO LOGIC IIx Music PRO LOGIC II Music DIMENSION PRO LOGIC IIx Music PRO LOGIC II Music CENTER WIDTH Pro Logic IIx Music and Pro Logic II Music center width. Moves the center channel output completely towards the center speaker or towards the front left and right speakers. A larger value moves the center channel output towards the front left and right speakers. Control range: 0 (center channel sound is output only from the center speaker) to 7 (center channel sound is output only from the front left and right speakers) Initial setting: 3 DTS Neo:6 Music C. IMAGE DTS Neo:6 Music center image. Adjusts the front left and right channel output relative to the center channel to make the center channel more or less dominant as necessary. Control range: 0. 0 to 1. 0 Initial setting: 0. 3 y The "PRO LOGIC IIx Music", "PRO LOGIC II Music", and "DTS Neo:6 Music" parameters can be set only when "SUR. Set the component selector switch to AMP and then press STANDARD on the remote control repeatedly to select "SUR. STANDARD" (see page 43). SOUND FIELD PROGRAMS 73 En SET MENU SET MENU You can use the following parameters in "SET MENU" to adjust a variety of system settings and customize the way this unit operates. E)LFE LEVEL F)DYNAMIC RANGE G)AUDIO SET [ ]/[ ]:Up/Down [ENTER]:Enter p p p p SET MENU . ;SIGNAL INFO [ ]/[ ]:Up/Down [ENTER]:Enter p p 76 En SET MENU 5 Press u / d repeatedly and then press ENTER to select and enter the desired submenu. The following display is an example where "SPEAKER LEVEL" is selected. PRESET/CH PRESET/CH 1 SOUND MENU Use this menu to manually adjust any speaker settings or compensate for video signal processing delays when using LCD monitors or projectors. 1 SOUND MENU 1/2 . A)SPEAKER SET B)SPEAKER LEVEL C)SP DISTANCE D)CENTER GEQ [ ]/[ ]:Up/Down [ENTER]:Enter 1 SOUND MENU 2/2 . E)LFE LEVEL F)DYNAMIC RANGE G)AUDIO SET [ ]/[ ]:Up/Down [ENTER]:Enter ENTER ENTER p p p p A-E/CAT. A-E/CAT. A-E/CAT. A-E/CAT. B)SPEAKER LEVEL . -__________+ FL;;;;;;;;;; FR;;;;;;;;;; C;;;;;;;;;; Speaker settings A)SPEAKER SET Use this feature to manually adjust any speaker settings. y If you are not satisfied with the bass sounds from your speakers, you can change these settings according to your preference. Front speakers FRONT SP Choices: SMALL, LARGE 6 Press u / d to select the desired parameter and then j / i to change the parameter settings. · Press j to decrease the value. PRESET/CH PRESET/CH FRONT SP SMALL >LARGE ENTER ENTER A-E/CAT. A-E/CAT. A-E/CAT. A-E/CAT. 7 Press SET MENU to exit from "SET MENU". SET MENU MENU SRCH MODE · Select "SMALL" (small) if you have small front speakers that do not reproduce low-frequency signals effectively. The low-frequency signals of the front left and right channels are directed to the speakers selected in "LFE/BASS OUT" (see page 78). · Select "LARGE" (large) if you have large front speakers that reproduce low-frequency signals effectively. All the front left and right channel signals are directed to the front left and right speakers. [. . . ] SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 16. 9. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. [. . . ]