User manual ROTEL RCC-945

[. . . ] Read all the instructions before connecting or operating the component. Keep this manual so you can refer to these safety instructions. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Immediately stop using the component and have it inspected and/or serviced by a qualified service agency if: · The power supply cord or plug has been damaged. · Objects have fallen or liquid has been spilled into the unit. [. . . ] Press the Open/Close button again to close the Disc Tray when you are done loading discs. Do not touch the Disc Carousel while it is turning or attempt to turn it by hand, as this also could cause damage. Use the Disc Skip buttons and let the Disc Carousel come to a stop before loading or removing discs. Disc Tray 8 and Open/Close Buttons 6 and u Selecting a Disc to Play In addition to the Disc buttons described above, the remote control may also be used to select discs. 12 Volt Trigger Input The RCC-945 can be activated by a 12 volt trigger signal. The trigger input accepts any control signal (AC or DC) ranging from 3 volts to 30 volts. When a cable is connected to the 12V input and a trigger signal is present, the RCC-945 is activated. When the trigger signal is turned off, the unit goes into standby mode. The front panel power indicator remains lit, but the display goes dark and the unit will not operate. NOTE: When using the 12V Trigger feature, leave the POWER button in the ON position. e Disc 1-5 Buttons (remote only) s Press the button that corresponds to the disc you want to select. Pressing one of the Disc 1-5 buttons when a disc is not playing simply selects the corresponding disc. If one of the Disc 1-5 buttons is pressed when a disc is playing, the RCC-945 stops playing the current disc, selects the corresponding disc, and begins playing track 1 of the disc. 9 English Playing Discs Play Buttons Press the Play Button to play the disc indicated in the Disc Display. The disc will begin playing with Track 1, unless another track has been selected before the Play button is pressed. The disc will remain selected but the track selection will go back to track 1. 0a Track Skip Buttons Press and hold the or buttons to quickly search a disc in the forward or reverse direction. For the first five seconds the search speed will be approximately four times normal playing speed. After three seconds the search speed will increase to approximately 20 times normal playing speed. The search function may be used when disc play has been temporarily stopped with the Pause function, however no sound is heard. The Search function will not go past the beginning or end of the selected disc. ][ When a disc is not playing: · Press the button to select the next track on the disc. Press and hold the button to advance more than one track on the disc. =i } } button to select the previous · Press the track on the disc. Press and hold the button to go back more than one track on the disc. { { HDCD discs are encoded with a high density data stream. During playback this high density data stream is decoded to a conventional digital signal. This HDCD encode/decode system greatly reduces the errors that are normally generated during the analog-to-digital, and then digital-to-analog, conversions. The HDCD system is automatically activated, and the HDCD Indicator 3 lights, whenever an HDCD disc is played. About HDCD® 3 RCC-945 CD Multi-Disc Changer 10 Track Calendar Display L shows the total number of tracks on the disc that is playing and the track that is currently playing. When a disc is selected, the Track Calendar Display shows the total number of tracks on the disc. [. . . ] Pressing the button searches backwards, but the search will not go beyond the beginning of the track that is playing. ] [ Playing Programmed Tracks Once a group of tracks has been programmed press the Play button to begin playing the tracks, starting with programmed selection 1. The selected tracks will play in sequence until the last selected track is over. When programmed tracks are playing, the Track Calendar L in the display shows only the numbers of the programmed tracks. If you press the stop button while playing programmed tracks, play resumes with programmed selection 1 when the play button is pressed again. The Repeat All Disc function works when programmed tracks are playing. [. . . ]