User manual ROTEL RD-1010

[. . . ] Heed all warnings and safety information in these instructions and on the product itself. You must allow a minimum of 10 cm or 4 inches of unobstructed clearance around the unit. Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation openings. If the unit is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper cooling. [. . . ] For example, if you set Dolby Pro Logic II movie mode as the default for all of your video inputs, the RD-1010 will automatically decode Dolby Digital 5. 1 and DTS soundtracks when they are played and use Pro Logic II matrix decoding for all other recordings. For stereo inputs such as CD and Tuner, you could select STEREO mode as the default for 2-channel playback or Dolby Pro Logic II music mode if you prefer to hear music sources in surround sound. 1, DTS 96/24, Dolby Digital, MP3, MPEG Multichannel, HDCD (96kHz), and PCM 2-channel (96kHz) digital signals are auto-detected and cannot be overridden. However, you can choose to use Dolby Digital Surround EX decoding for any Dolby Digital 5. The following topics describe in detail the ºmanual surround mode options available for each type of recording: · Press the SUR+ button on the remote, then press the +/­ buttons to change between DD 5. Press the SUR+ button on the remote, then use the +/­ buttons to step through five optons: DD 2. 1 channel, DD Surround EX center back processing, DD with Pro Logic IIx Music center back processing or DD with Rotel XS center back processing. You should typically select Surround EX or discs that are labeled Dolby Digital Surround EX. 1 channel discs, Dolby Pro Logic IIx Music or Rotel XS processing will provide a more diffuse surround effect than the more highly localized Dolby EX decoding and will probably be the better 6. You can also repeatedly press the DOLBY PLII/3ST button on the front panel until the desired center back channel option is selected. NOTE: When playing any Dolby Digital source, you can select one of three dynamic range control settings. Press the SUR+ button on the remote, then press the +/­ buttons to change between DTS 5. Press the SUR+ button on the remote, then use the +/­ buttons to step through the optonal modes: DTS 2. 1 channel, DTS with Rotel XS center back processing, DTS with Pro Logic IIx Music center back processing, or DTS with Pro Logic IIx Cinema center back processing (available only for 7. You can also repeatedly press the DTS Neo:6 button on the front panel until the desired option is selected. Press the SUR+ button on the remote, then use the +/­ buttons to step through three optional modes: DTS 2. On the front panel, press the DTS Neo:6 button while playing a DTS source to step through the same options. Press the SUR+ button on the remote, then use the +/­ buttons to step through the optonal modes: DTS 2. 0 channel downmix, DTS 96, or DTS 96 with Rotel XS center back processing. You can also repeatedly press the DTS Neo:6 button on the front panel until the desired option is selected. This group of recordings includes any nonDolby Digital 2-channel signal from the RD-1010's digital inputs. [. . . ] To memorize USER DEFAULT settings: Many of the current configuration settings can be stored as a USER DEFAULT, which can be activated at any time from this menu screen. To save the current settings as a USER DEFAULT, place the highlight on the SET USER DEFAULT line using the UP/DOWN buttons and use the +/­ buttons to change the setting to YES. To return to the MAIN menu without saving any changes, change all entries on the screen to NO and press the ENTER button. NOTE: If there is insufficient memory to store a USER DEFAULT configuration file, the SET USER DEFAULT option will not be available. [. . . ]