User manual ROTEL RSP-960AX

[. . . ] Audio input terminals (AV-2) Connects to a camcorder, video game, etc. Video input terminal (AV-2) Connects to a camcorder, video game, etc. / CH Connecting to an antenna via a VCR You can also connect the TV set to the tuner on a VCR using the connection shown below. TV VCR MENU/PRESET button Tunes the channels. Tunes or sets the channels. / Volume up/down buttons Adjusts the volume. Makes adjustments in PRESET. Using headphone To antenna in terminal To RF out terminal [ Behind the door ] Insert headphone plug into headphone jack to listen to audio with headphone. [. . . ] Used for MENU setup. TIMER 7 Switches between one- or two-digit mode channel selection. CH · Press MENU/PRESET for more than two seconds, the language select mode appear. · Pressing MENU/PRESET changes the screen as shown below. Language AUTO MANUAL Normal screen CH CH MENU/PRESET CH CH / CH · Press MENU/PRESET until normal screen appears. Calls the TIMER screen. FEATURE Selects the channel. Used for MENU setup. TV/VIDEO Channel selection FEATURE CH-SET TIMER NORMAL PICTURE 1 4 2 5 8 0 3 6 9 1 5 Calls the FEATURE screen. Mutes the sound and restores sound to previous level. !Using CH / CH 7 CH-SET PICTURE Calls the CH-SETTING screen. TV NORMAL Calls the PICTURE screen. · Press CH and channels change as shown below. / 2 / 1 / 0 . . . CH CH CH CH FEATURE CH-SET TIMER NORMAL PICTURE @ With the number buttons (on remote control) Displays the channel and timer settings on the screen. 5 · To select a one-digit channel, such as 5, press . If "5-" is indicated, press to select one-digit input, 5 and then press again. · To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press . TV Resets all settings. -115 PAL B/G Installing batteries in the remote control unit a With your thumbnail, pull up at the slit to open the battery cover. b Insert two batteries (size AA). c Replace the battery cover. Adjusting volume !Adjust volume using / . · The volume bar disappears approximately three seconds after the volume has been adjusted. VOLUME 10 · Channels that have been skipped cannot be selected by CH · The AV1, AV2 input channels cannot be selected using CH these channel. / / CH CH . Use TV/VIDEO to select E6 PRESETTING CHANNELS E7 SETTING AND ADJUSTMENT Auto channel tuning Automatically tunes in and presets receivable TV stations. Channel setting Enables individual channel setting. AUTO(B/G) VHF 1 48. 25MHz !again to display AUTO mode screen. changes the screen as shown below. MANUAL Normal screen AUTO !to put TV set into Standby mode. Power indicator (Flashing) · Power indicator will flash to indicate On Timer is set. · When the preset length of time has passed, " 0:00" flashes in red. 0:03 0:02 0:01 0:00 CH CH Mute Silences the sound. FEATURE CH-SET TIMER NORMAL PICTURE Flashing !Press TV . " appears on the screen, and the sound E9 FEATURES · Press , " is silenced. Blue screen Automatically turns the screen blue if a broadcast signal is not received. @ Press level. , the volume returns to its previous is pressed at any time. !Press @ Press # Press No signal FEATURE to call FEATURE screen. / to select "BLUE BACK" to "ON" or "OFF". · Mute will be cancelled if the FEATURE BLUE BACK ON FEATURE to return to normal screen. :ADJUST When BLUE BACK is set to "ON". Blue screen TV off (Indicator) after 5 seconds after 15 minutes Standby mode Power indicator lights up dimly · This function also works in the Standby mode. Power is automatically turned on five minutes before the preset length of time expires. The TV set automatically returns to the Standby mode approximately 1 minute if no buttons are pressed on the TV set or remote control. · The Reminder is cancelled if POWER on the TV set is pressed or if the power is otherwise interrupted. · Poor reception due to weak signals and too much noise may activate BLUE BACK, despite the presence of a broadcast signal. To continue watching TV under these conditions, switch "BLUE BACK" to "OFF". [. . . ] Example use of front terminals PAL Press . 5 · The channel previously viewed returns to the screen. PAL 7 Example: After switching from channel 5 to channel 7, the channel will change to channel 5. Press return to channel 7. PAL 5 TV VCR is pressed, again to PAL TV/VIDEO 7 TV/VIDEO 1 4 7 2 5 8 0 3 6 9 Camcorder Number buttons Video Game CH CH TV / Video selection Switches between TV broadcasts and AV input programmes. · Each time you press the TV/VIDEO , the input switches between AV1, AV2 and TV programme. Behind the door PICTURE FEATURE CH-SET TIMER NORMAL To Audio/Video out terminals Yellow : To VIDEO White : To AUDIO AV1 AV2 TV Example use of rear terminals 25 PAL B/G TV For Playback DVD Player For Recording and Editing VCR Yellow : To VIDEO White : To AUDIO To Audio/ Video out terminals To Audio/ Video in terminals VCR To Audio/ Video out terminals · The audiovisual cords required to connect the TV set with video equipment may differ from those shown in the above diagram. See the operation manual of your video equipment for connection details. [. . . ]