User manual ROTEL RSX-1055

[. . . ] Owner's Manual RSX-1055 Surround Sound Receiver SURROUND SOUND RECEIVER RSX-1055 POWER VOLUME 1 2 3 4 5 TUNING BAND CD TUNER TAPE VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 6 7 8 9 0 DIRECT MONO MEMORY 2CH DOLBY PLII/3ST DTS NEO 6 DSP MULTI INPUT DYNAMIC RANGE ZONE REC Notice The COMPUTER I/O connection should be handled by authorized person only. FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If a station is found, a TP indicator lights in the front-panel display. If no station is located, the tuner will return to the last previously tuned station. Cancel the TP function by pressing any other button. Do not plug any system component into an AC source until all connections have been properly made. NOTE: Video cables should have a 75 ohm impedance rating. The S/PDIF digital audio interface standard also specifies a 75 ohm impedance and all good digital cables adhere to this requirement. Because the video and S/PDIF standards are so close, you can use a video cable for digital audio data transmission. Do NOT substitute conventional audio interconnect cables for digital or video signals. Standard audio interconnects will pass these signals, but their limited bandwidth reduce performance. When making signal connections, connect LEFT channels to LEFT channel jacks and RIGHT channels to RIGHT channel jacks. All RCA-type connections on the RSX-1055 follow these standard color codes: Left channel audio: white RCA jack Right channel audio: red RCA jack Composite video: yellow RCA jack On a PAL standard monitor, the OSD cannot be displayed until a video signal is present, irrespective of the type of video cables in use. For setup, connect the video output from your DVD player and select its input on the RSX-1055. The OSD will be displayed as an overlay to the video signal from the DVD player. NOTE: TA Button Searches for an RDS station broadcasting special traffic announcements: 1. The tuner will attempt to find an RDS station broadcasting traffic announcements. If no station is located, the tuner will return to the last previously tuned station. Cancel the TA function by pressing any other button. Composite and S-Video: With certain exceptions, a system should be connected with either all Composite or all S-Video cables. S-Video signals from sources cannot be sent to a TV set from the RSX-1055 TV MONITOR outputs with a Composite video cable. Conversely, Composite video signals from sources cannot be sent to a TV set from the RSX-1055 TV MONITOR outputs with an S-Video cable. Therefore, Composite and S-Video connections cannot be easily "mixed" in a system. However, both Composite and S-Video cables may be connected from the RSX-1055 TV MONITOR outputs to both Composite and S-Video inputs on a TV or projector. This dual connection from the RSX-1055 will provide limited S-Video capability in a system that is predominantly connected with Composite video cables, however Each source input must be properly configured using the INPUT MENU of the ON-SCREEN DISPLAY system. We recommend going to this menu after connecting each source to configure it as desired. See the INPUT MENU section for information. NOTE: RSX-1055 Surround Sound Receiver 22 it requires switching the input on the TV monitor when changing from an S-Video to an RCA Composite connected source. When both Composite and S-Video cables are connected from the same source, both Composite and S-Video signals are available at the RSX-1055's TV MONITOR outputs, allowing the selection of the desired signal with the TV input selector. [. . . ] Then, move the highlight to the FACTORY DEFAULT line and change the setting to YES as described above. Press the ENTER button to proceed with resetting the FACTORY DEFAULT settings and changing the TUNER SETTING. To return to the MAIN menu without resetting the FACTORY DEFAULT and TUNER settings, change the entry to NO and press the ENTER button. NOTE: Changing the default TUNER SETTING can only done at the same time as restoring the FACTORY DEFAULT settings. Therefore, we recommend selecting your default TUNER SETTING and resetting to the FACTORY DEFAULT settings as the first step in configuring the unit, before you change or memorize any other configuration settings. The DEFAULT SETUP menu provides access to five functions: · Restoring all features and settings to the original FACTORY DEFAULT settings. [. . . ]