User manual ROTEL RSX-1065

[. . . ] Owner's Manual RSX-1065 Surround Sound Receiver SURROUND SOUND RECEIVER RSX-1065 DIGITAL PRO LOGIC dts DSP PRESET RDS ZONE OPT COAX 1 2 3 4 5 A 5. 1 7. 1 FL C FR SL SR SW Sbl Sbr Sb ST TUNED VOLUME CD TUNER TAPE VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 2CH 3 STEREO PRO LOGIC II DSP MULTI INPUT DYNAMIC RANGE ZONE REC 1 2 3 4 5 TUNING BAND BASS 6 7 8 9 0 DIRECT MONO MEMORY TREBLE POWER RSX-1065 Surround Sound Receiver 2 Important Safety Instructions WARNING: There are no user serviceable parts inside. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. [. . . ] We strongly advise that you NOT substitute conventional audio interconnect cables for digital or video signals. Standard audio interconnects will pass these signals, but their limited bandwidth reduce performance. When making signal connections, connect LEFT channels to LEFT channel jacks and RIGHT channels to RIGHT channel jacks. All RCA-type connections on the RSX-1065 follow these standard color codes: Left channel audio: white RCA jack Right channel audio: red RCA jack Composite video: yellow RCA jack CD Inputs Connect the left and right analog outputs from your CD player to the input jacks labeled CD. TAPE Inputs and Outputs The RSX-1065 provides a pair of inputs and a pair of record outputs for connecting an analog audio tape deck. The analog source signal available for recording at the TAPE outputs is selected with the REC button on the front-panel (or the ZONE button on the remote) and its label appears in the display. If the TAPE input signal is selected as the recording source, its signal will not be available at the TAPE output, but will be available at the VIDEO outputs for recording. Connect the left and right analog outputs from an audio tape deck to the TAPE IN jacks. Connect the TAPE OUT jacks to the inputs on the audio tape deck. Each source input must be properly configured using the INPUT MENU of the ON-SCREEN DISPLAY system. We recommend going to this menu after connecting each source to configure it as desired. See the INPUT MENU section for information. NOTE: Composite and S-Video: With certain exceptions, a system should be connected with either all Composite or all S-Video cables. S-Video signals from sources cannot be sent to a TV set from the RSX-1065 TV MONITOR outputs with a Composite video cable. Conversely, Composite video signals from sources cannot be sent to a TV set from the RSX-1065 TV MONITOR outputs with an S-Video cable. Therefore, Composite and S-Video connections cannot be "mixed" in a system. RSX-1065 Surround Sound Receiver 20 Video Source Inputs There are input connections for five video source components. Each of the five provides a pair of RCA inputs for analog audio signals. Each of the five also provides a choice of an RCA composite video input or S-Video input for the video signal from the source component. In addition, two of the video source inputs (Video 1 and Video 2) also feature Component Video input connections as an alternative to the composite video or S-Video connections. VIDEO 1­5 Composite Video Inputs If you use the RCA composite video connections for a source component, connect the RCA video output of the source component to one of the video inputs labeled COMPOSITE IN. Use a standard 75 ohm video cable. MULTI Channel Audio Inputs A set of RCA inputs accepts seven channels of analog signals from a 5. 1 or 6. 1 channel processor or source component. When selected with the front-panel MULTI INPUT button or remote EXT IN button, this input overrides any other audio input signal. Use audio interconnect cables to connect the outputs of the source component to the RCA jacks labeled MULTI INPUT, making sure that you observe proper channel consistency, i. e. Depending on your system configuration, you will make six connections (FRONT RIGHT/FRONT LEFT/REAR RIGHT/REAR LEFT/ CENTER/SUBWOOFER), seven connections (FRONT RIGHT/FRONT LEFT/ REAR RIGHT/ REAR LEFT/CENTER/CENTER BACK/SUBWOOFER). VIDEO 1­5 S-Video Inputs S-Video signals use a special cable which divides the video signal into several elements carried by separate conductors, providing higher quality than the standard RCA composite cables. If you choose to use an S-Video input connection from a source component, connect the S-Video output of that component to one of the inputs on the RSX-1065 labeled S-VIDEO IN using a standard S-Video interconnect cable. There is no need to use more than one type of video connection from a source component. We recommend selecting one type of video connection and using it for all video inputs and outputs. [. . . ] +/­ KEY=change UP KEY=up DWN KEY=down The DEFAULT SETUP menu provides access to four functions: · Restoring all features and settings to the original FACTORY DEFAULT settings. · Changing the tuning functions and displays for use in North America or Europe. To restore the FACTORY DEFAULT settings: Place the highlight on the FACTORY DEFAULT line using the UP/DOWN buttons and use the +/­ buttons to change the setting to YES. Press the ENTER button to proceed with resetting the FACTORY DEFAULT settings. [. . . ]