User manual ROTEL RSX-1067

[. . . ] Owner's manual RSX-1067 Surround Sound Receiver SURROUND SOUND RECEIVER RSX-1067 VOLUME CD TUNER TAPE VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 2CH DOLBY PL /3ST DTS Neo 6 DSP MULTI INPUT MUTE ZONE REC 1 2 3 4 5 TUNING BAND LF 6 7 8 9 0 DIRECT MONO MEMORY HF STANDBY > 10 cm > 4 in SURROUND SOUND RECEIVER RSX-1067 > 10 cm CD TUNER TAPE VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 2CH DOLBY PL /3ST DTS Neo 6 DSP MULTI INPUT MUTE ZONE REC VOLUME > 10 cm > 4 in > 4 in 1 2 3 4 5 TUNING BAND LF 6 7 8 9 0 DIRECT MONO MEMORY HF STANDBY > 10 cm > 4 in Notice The COMPUTER I/O connection should be handled by authorized person only. Important Safety Instructions WARNING: There are no user serviceable parts inside. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. [. . . ] Manual settings available from the front panel and/or the remote might be used when you want to play: · Standard 2-channel stereo (left/right speakers only) with no surround processing. · Downmixed 2-channel playback of Dolby Digital 5. 1 or DTS recordings. · Dolby 3-channel stereo (left/right/center) of 2-channel recordings. · One of four MUSIC modes for DSP concert hall simulation from 2-channel recordings. · Dolby Pro Logic II cinema or music mode matrix decoding of 2-channel recordings. · DTS Neo:6 cinema or music mode matrix decoding of 2-channel recordings. · Dolby Digital Surround EX decoding of Dolby Digital 5. 1 channel recordings or Dolby Digital Surround EX discs that do not trigger automatic decoding. · HDCD (non 96kHz) and PCM 2-channel (non 96kHz) digital signals can be overridden to Dolby Pro Logic II, Dolby 3-Stereo, DTS Neo:6, Music 1 ­ 4, 5CH Stereo, 7CH Stereo, and Stereo. · Dolby Digital 2-channel Stereo can be overridden to Dolby Pro Logic II, Dolby 3-Stereo, and Stereo. The following topics describe in detail the manual surround mode options available for each type of recording: Dolby Digital 5. 1 discs Dolby Digital Surround EX discs Dolby Digital decoding is auto-detected and cannot be overridden. You may, however, select a 2 channel downmix of 5. 1 channel recordings. In a 6. 1ch or 7. 1 ch system, you can also choose Dolby Surround EX, Dolby Pro Logic IIx Music, Dolby Pro Logic IIx Cinema (7. 1ch only), or Rotel XS processing for center back channels. NOTE: In addition to the options that follow, you can press the 2CH button on the front panel or the remote to toggle between 2-channel downmix and multichannel playback. A digital signal coming into the RSX-1067 will be recognized and properly decoded. However, on a DVD with multiple soundtracks, you must tell the DVD player which one to send to the RSX-1067. For example, you may need to use the DVD's menu system to select the Dolby Digital 5. 1 or DTS 5. 1 soundtrack rather than the default Dolby Digital 2. 0 Dolby Surround soundtrack. NOTE: · On a 5. 1 system. Press the SUR+ button on the remote, then press the +/­ buttons to change between DD 5. 1 channel or DD 2. 0 channel downmix playback. Press the SUR+ button on the remote, then use the +/­ buttons to step through five options: DD 2. 0 channel downmix, DD 5. 1 channel, DD Surround EX center back processing, DD with Pro Logic IIx Music center back processing or DD with Rotel XS center back processing. You should typically select Surround EX or discs that are labeled Dolby Digital Surround EX. For standard 5. 1 channel discs, Dolby Pro Logic IIx Music or Rotel XS processing will provide a more diffuse sur- Additionally, you can configure a default surround mode for each input using the INPUT SETUP menu (see the Setup section of this manual). Combined with the auto-detection of Dolby Digital 5. 1 and DTS, this default surround setting makes operation of the RSX-1067 surround modes totally automatic. For example, if you set Dolby Pro Logic II movie mode as RSX-1067 Surround Sound Receiver 28 round effect than the more highly localized Dolby EX decoding and will probably be the better 6. 1 channel options for non-Surround EX discs. Selecting DD 5. 1 forces the center back channel processing off for conventional 5. 1 channel playback. You can also repeatedly press the DOLBY PLII/3ST button on the front panel until the desired center back channel option is selected. Press the SUR+ button on the remote, then use the +/­ buttons to step through six optons: DD 2. 0 channel downmix, DD 5. 1 channel, DD Surround EX center back processing, DD with Pro Logic IIx Music center back processing, DD with Pro Logic IIx Cinema back channel processing, or DD with Rotel XS center back processing. [. . . ] To return to the MAIN menu without resetting the FACTORY DEFAULT settings, change the entry to NO and press the ENTER button. RSX-1067 Surround Sound Receiver 44 MORE INFORMATION OSD menus are not displayed on TV Monitor. · Go to Setup menus and configure OSD menus to be displayed on the TV monitor. · In some PAL systems, the menus may not be displayed unless there is an active video signal. · When using progressive scan video signals, make sure that the progressive mode is selected for that video input in the OTHER OPTIONS setup menu. [. . . ]