User manual ROTEL RX-1050

[. . . ] Owner's Manual RX-1050 AM/FM Stereo Receiver AM/FM STEREO RECEIVER RX-1050 POWER SPEAKER A TUNING BAND TREBLE PHONO CD TUNER TAPE VIDEO 1 PHONES B TUNE/ PRESET MONO MEMORY BASS VIDEO 2 VIDEO 3 VIDEO 4 ZONE REC RX-1050 Surround Sound Receiver Important Safety Instructions WARNING: There are no user serviceable parts inside. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. [. . . ] For European FM stations, press two digits following the decimal point as shown in the second example. EXAMPLES: TUNING Buttons CH TUNING Buttons The buttons labeled TUNING on the front panel or CH UP/DOWN on the remote control provide two different tuning functions, depending on the mode of operation. In the normal FREQUENCY TUNING mode, press a TUNING button and release to manually jump up or down to the next station frequency, regardless of whether or not a station is broadcasting on that frequency. For auto scan tuning, press and hold the TUNING button for approximately one second. An AUTO indicator appears in the front panel display and the tuner begins automatically scanning up or down through the frequencies until the next available station is detected. If this is not the desired station, repeat the automatic tuning procedure to find the next station. In the PRESET TUNING mode, press a TUNING button and release to jump up or down to the next memorized station preset. Switch between FREQUENCY and PRESET tuning modes by pressing the SHIFT button and then the BAND/TV button on the remote control. A PRESET indicator appears in the display when PRESET TUNING is activated. NOTE: Several indicators in the front panel display assist tuning. A large display shows the tuned frequency and increases or decreases during tuning. A TUNED indicator lights when a sufficiently strong signal is received. A ST indicator lights when a stereo FM signal is received. TUNE/PRESET Button [SHIFT] TV Button The TUNE PRESET button toggles between FREQUENCY TUNING mode (the CH TUNING buttons advance to the next station frequency) and PRESET TUNING mode (the CH TUNING buttons advance to the next memorized station preset). To change modes using the remote, press the SHIFT button and then the TV button. A PRESET indicator in the front panel DISPLAY lights when the PRESET mode is active. NUMERIC Buttons: Station Presets The RX-1050 can store up to 30 station presets for recall at any time using the NUMERIC buttons on the remote control. A MEMORY indicator flashes for five seconds in the front panel display. While the MEMORY indicator is flashing, press the number of the preset where you wish to store the station frequency. A previously stored frequency is erased from memory when a new frequency is memorized for the same preset number. To tune to a previously memorized station, just press the preset number on the NUMERIC buttons. To tune to preset 15, press the 1 button and then press the 5 button. NOTE: If the TUNER is not already the selected INPUT SOURCE, selecting a station preset will automatically switch to the TUNER input and tune the memorized station. (USA FM) 87. 50MHz (Europe FM) 87. 50MHz (all AM) 1610kHz Press 8>7>5 Press 8>7>5>0 Press 1>6>1>0 Preset Scanning [SHIFT] MUTE Buttons This shift function activates a PRESET SCANNING feature, playing each memorized preset station for five seconds before moving to the next. Using the remote, press the SHIFT button and then the MUTE button to begin scanning. To stop the PRESET SCANNING on the desired station, press the SHIFT button and then the MUTE button. The NUMERIC buttons can also be used for direct access tuning (see below). RX-1050 AM/FM Stereo Receiver 14 MONO Button The MONO button changes the FM mode from stereo reception to mono reception. In stereo mode, a stereo signal will be heard if the station is broadcasting a stereo signal and there is sufficient signal strength. In mono mode, a mono signal will be heard even if the station is broadcasting a stereo signal. Once a custom label is programmed, the new name appears when that source is selected for either listening or recording. [. . . ] Controlling Zone 2 from the front-panel is accomplished by pressing the ZONE button, which temporarily puts the RX-1050 in Zone 2 control mode, even if the unit is in standby mode. When the ZONE button is pressed, the FL DISPLAY shows the current status of ZONE 2 for ten seconds, during which time you can use the VOLUME control and INPUT SOURCE buttons to change the ZONE 2 settings. When ZONE 2 is off, the POWER LED is steadily lit. Controlling Zone 2 from the Remote Location With a properly configured IR repeater system, you have full control of Zone 2 using an RR-939B remote from the Zone 2 location. You can select and operate a source, adjust the volume, and turn Zone 2 on or off. [. . . ]