User manual ROTEL RX-1052

[. . . ] Owner's Manual RX-1052 AM/FM Stereo Receiver AM/FM STEREO RECEIVER RX-1052 STANDBY ZONE SPEAKERS A TUNING BAND TREBLE PHONO CD TUNER TAPE VIDEO1 TUNE/ PRESET B MONO MEMORY BASS VIDEO2 VIDEO3 VIDEO4 ZONE SEL > 10 cm > 4 in AM/FM STEREO RECEIVER RX-1052 > 10 cm > 4 in STANDBY > 10 cm SPEAKERS A TUNING BAND TREBLE PHONO CD TUNER TAPE VIDEO1 > 4 in TUNE/ PRESET B MONO MEMORY BASS VIDEO2 VIDEO3 VIDEO4 ZONE SEL > 10 cm > 4 in Notice The COMPUTER I/O connection should be handled by authorized person only. Important Safety Instructions WARNING: There are no user serviceable parts inside. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. [. . . ] Then, come instructions for configuring the RX-1052 for various types of recordings. Finally, there are instructions for additional features and Zone 2 operations. Throughout this manual, numbers in gray boxes refer to the RX-1052 illustration at the front of this manual. When both appear, the function is found on both the RX-1052 and the remote. When only one appears, that function is found only on the RX-1052 or the remote. The display can be turned off, if desired. See the DISP button section for instructions. Remote Sensor This sensor receives IR signals from the remote control. Do not block this sensor unless an external IR receiver is used. STANDBY Button POWER Switch The front panel STANDBY button activates or deactivates the unit. The rear panel master POWER switch must be in the ON position for the standby function to operate. ON/OFF Buttons The power ON and OFF buttons on the remote provide discrete ON/OFF commands which duplicate the function of the front panel STANDBY button. Press the ON button to activate the unit; press the OFF button to put the unit into standby mode. The rear panel master POWER switch must be in the ON position for the standby function to operate. Layout of Controls, Buttons, and Features The following is a brief overview of the controls, buttons, and features of the RX-1052. Details concerning the use of these controls are provided in subsequent sections of this manual describing various operations. VOLUME Knob VOLUME Buttons The large rotary control on the front panel and the pair of VOLUME buttons on the remote provide the master VOLUME control, adjusting the output level of all channels simultaneously. MUTE Button Push the MUTE button on the remote once to turn the sound off. Press the button again to restore previous volume levels. RR-AT93 Remote Control The RX-1052 includes a remote control that operates the RX-1052. The RR-AT93 is also preprogrammed to operate many Rotel CD and DVD players. Pressing the volume buttons on the remote also cancels the muting function. NOTE: Front-panel Display The display on the front panel of the RX-1052 provides information about the status of the unit, tuner reception, and special features. The main portion of the display typically shows the current input source (or radio station frequency). A TUNED indicator lights when a sufficiently strong station is being received. A STEREO indicator lights when a stereo FM signal is being received. Tone Controls BASS and TREBLE controls on the front panel increase or decrease the audio signal's low and high frequency content respectively. Rotate clockwise to increase output in the respective frequency range and counterclockwise to reduce it. The center 0 position removes each control from the audio path for maximum signal integrity. NOTE: Bass and treble can also be adjusted from the remote by pressing the ENTER button repeatedly to select bass or treble, and adjusting up or down using the +/­ buttons. 17 English Headphones Jack This jack accepts a standard 1/4 inch stereo headphone plug. Use an adaptor if your headphones have a smaller plug. NOTE: Pressing the ZONE button without first specifying a zone with the SEL button, allows Zone 2 control. The ENTER button is also is used following the press of the LABEL button to programming custom labels. Inserting a headphone plug does not automatically disable the speaker outputs. Use the SPEAKER buttons described in the next section to turn the speakers on or off during headphone listening. NOTE: A long press of the ZONE button activates the Party mode, selecting the source from the main room for use by all of the remote zones plus the record outputs. BAND Buttons Press the BAND button on the front panel or the remote to toggle between AM and FM reception. SEL Buttons REC Button Press the front panel SEL button or the remote control REC button to select the desired zone for additional changes such as changing the input, adjusting the volume, or turning a remote zone on or off. Repeatedly press the button until the desired zone appears in the front panel: RECORD > ZONE 2 > ZONE 3 > ZONE 4. Once the desired zone appears, you have 10 seconds to make the desired change. [. . . ] To select a different analog input source, press one of the INPUT buttons on the remote. You can also use the CHARACTER +/­ buttons to step through the source inputs. Select the "SOURCE" option to link the input for the selected zone to the input used for listening in the main room. When linked, changing the input in the main room will automatically change it in the remote zone, too. Troubleshooting The unit does not turn on. [. . . ]