User manual RUSSOUND A-LC2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND A-LC2. We hope that this RUSSOUND A-LC2 user guide will be useful to you.


RUSSOUND A-LC2 : Download the complete user guide (243 Ko)

Manual abstract: user guide RUSSOUND A-LC2

Detailed instructions for use are in the User's Guide.

[. . . ] · The A-LC2 can also be used to connect the audio output of a television so TV sound can be heard through a room's speakers. 3 SENSITIVITY ADJUSTMENT The sensitivity adjustment determines the level of signal needed before the A-LC2 will switch from the main source to the local source. Try the lowest level first (fully counter-clockwise) and gradually raise the level until the switching occurs. Use a Philips-head screwdriver. Model A-LC2 Local Source Input for A-BUS® System Instruction Manual A-BUS® SYSTEM OVERVIEW The A-LC2 is an in-wall, A-BUS® Module that automatically selects between an independent local source (e. g. , a CD player in the room) and the main source of an A-BUS® system. [. . . ] The Russound® A-KP2 Amplified Keypad (with built-in IR receiver) and A-VC Amplified Volume Control are examples of A-BUS® Amplified Modules. A-BUS® Hubs: All components of the A-BUS® system must be wired centrally to a Hub located near your source equipment. The Hub provides the connection for source equipment, volume controls, infrared emitters and power supply. The Russound® A-PS 24VDC/2. 5A unit is an example. A-LC2 FEATURES 1) 2) 3) 4) 5) Stereo audio input Automatic switching between local and main source Switching sensitivity adjustment Switching delay adjustment Decora® faceplate INSTALLATION NOTES · Using the A-LC2 requires that the status feature be disabled on the A-BUS® Hub as well as on ALL A-BUS® Amplified Control Modules in the system unless it is being used. · Before connecting the A-LC2: - Make sure that the A-PS power supply is not connected to the A-BUS® Hub or, if you are using an A-BUS® Ready receiver, that the receiver is off. - Make sure that the STATUS input on the A-BUS® Hub is not connected. · The recommended maximum length for use with standard CAT-5 cable is 250 feet. · Once all of the connections have been made, the A-PS power supply can be connected to the A-BUS® Hub or, if you are using an A-BUS® Ready receiver, the receiver may be turned on. 5 MOUNTING Locate the A-LC2 near the local source. Check all connections and test the system's operation before installing the A-LC2 into the wall. Using the included hardware, install the A-LC2 into a standard UL/CSA approved electrical J-Box as shown. A-LC2 SPECIFICATIONS Power Requirements: Input Sensitivity: Switching Delay: CAT-5 Connection: Dimensions (in-wall): Weight: 24VDC, 24mA 35mV to 280mV 10 sec. 110 Punchdown 1. 75"W x 2. 875"H x 1. 75"D (45x73x45mm) 6 oz. (170g) 6 OPERATION When the A-LC2 senses an audio signal at its local input, the main audio is switched out locally, the local audio is switched in, and the status light on the connected Amplified Control Module turns on (if not already on). When local audio is no longer sensed, the A-LC2 will switch back to the main audio. If the main audio is not running, the Amplified Control Module will automatically turn off (AKP2) or mute (A-VC), only if "Status" is enabled on the hub and there is a switched outlet on the main audio source. 1 CAT-5 CONNECTIONS A CAT-5 cable is used to connect the A-LC2 to a keypad output on an A-BUS® Hub or A-BUS® Ready receiver, and to an A-BUS® Amplified Contol Module. For clean installations, use RJ-45 CAT-5 patch cables (use T568A RJ-45 wire configuration) to connect from the Hub to an RJ-45 Wall Plate (optional), and then wire from the Wall Plate to the A-LC2 (see diagram). The A-LC2 and the Amplified Control Module have 110 punchdown connectors for the 8 individual conductors of the CAT-5 cable (use a punchdown tool with a 110 blade to insert conductors). NOTE: When wiring directly to the A-LC2 (i. e. , not using an RJ-45 Wall Plate) crimp on a male RJ-45 connector using the T568A RJ45 wire configuration for connection to the hub. Rev. [. . . ] Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. Russound sells products only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND A-LC2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND A-LC2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.