User manual RUSSOUND CA-LCD2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND CA-LCD2. We hope that this RUSSOUND CA-LCD2 user guide will be useful to you.


RUSSOUND CA-LCD2 : Download the complete user guide (160 Ko)

Manual abstract: user guide RUSSOUND CA-LCD2

Detailed instructions for use are in the User's Guide.

[. . . ] NOTE: 250ft run of wire maximum per keypad is recommended. 5 SRM-2. 1 If you are using the SRM-2. 1 speaker relay module, wire the +, terminals of the CA-LCD to the SRM-2. 1 +, - terminals as shown. Digital Display Keypad for CAi-Series System Instruction Manual CA-LCD2 OVERVIEW Before the keypad is installed into the j-box, turn on the power so that you can operate the keypad. The amber and the green back light brightness can be individually set. Press and hold the lamp button on the front of the keypad until the backlight switches to the other color. [. . . ] To control the functions of the CA-LCD2 keypad, use the CA Remote control. The CA remote control will operate the lamp, source selection, volume up/down and room on/off. h) IR confirmation LED: This LED will flash to confirm the reception of an IR signal from a remote control through the IR receiver. 2 PUNCHDOWN TERMINALS The CAi Keypads come with 110 punchdown terminals. These terminals are quick, easy to install and provide a strong connection. Press wires into punchdown terminal with punchdown tool as shown. 3 CLEAN INSTALLATION For clean installations, we recommend using RJ-45 jumpers to run from the CAi controller to an RJ-45 Wall Plate then running your keypads from the Wall Plate. The CA-LCD2 keypad is an accessory to the CA6. 4i and CA4. 4i audio distribution systems. The CA-LCD2 controls volume and source selection for the zone that it is in. The backlit LCD display shows the source that is selected as well as the volume level. Each of the four sources can be designated by easily selecting one of the 23 source labels with a quick selection from the front of the keypad. Volume, source selection, room on/off and backlight operation can be operated from the CA-LCD2 remote. The IR receiver on the CA-LCD2 will also pass IR to operate source components. A 12-VDC trigger output allows operation of 12 volt-triggered products like the Russound® SRM-2. 1 speaker relay module. Russound® products are guaranteed to provide years of enjoyment. 8 CAUTION These service instructions are for use by qualified personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 9 IMPORTANT SAFETY INSTRUCTIONS Do not install near any heat source such as radiators, heat registers, stoves or other apparatus (including amplifier) that produce heat. Follow all instructions. CA-LCD2 FEATURES Power On/Off, Volume Up/Down buttons Selectable amber or green back lighting Backlit LCD readout Choose from custom list of source names Built-in IR receiver IR control of keypad via optional CA-LRC1 remote IR control of source components in an CAi system that uses IR Emitters 8) LED indicator for IR confirmation 9) Volume Trims for setting max. allowable level and L/R balance 10) Decora® faceplate 1) 2) 3) 4) 5) 6) 7) 4 INSTALLING THE KEYPADS · The best infrared remote performance is achieved with the keypad away from any direct sunlight. · Choose a place that is easily seen from the position where a person is most likely to be located. · Check whether or not you can route the wire to the location you have chosen. 20 cubic inches) or p-rings and cut in the boxes using a key-hole saw or sheetrock knife/hand saw. [. . . ] Russound® assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by Russound®. Damage to or destruction of components due to improper use voids the warranty. To return for repairs, the unit must be shipped to Russound® at the owner's expense, along with a note explaining the nature of the service required. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND CA-LCD2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND CA-LCD2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.