Detailed instructions for use are in the User's Guide.
[. . . ] Aim the remote control at the the TV and slowly alternate between pressing PWR and TV. NOTE: In the search mode, the (C)ALRC1 will send IR codes from its library to the selected device, starting with the most popular code first. To search for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i. e. , CBL, VCR, TV, 1, 2, 3, or 4).
Interaction of learned keys and keymover:
· If both a learned function and a keymoved function are placed on the same key, whichever was programmed last will take precedence. Keymover always uses the key's original function as the source.
Limitations on Learning
NOTE: If a code digit is "0", the LED will not blink. [. . . ] High levels of "nature light" or Energy efficient fluorescent lights, could interfere with a learning event. · In general, it is not recommended to learn a function to the Record Key. The Record Key requires a double key press to send the record function in normal operation. The double key press is lost when the Record key is involved in most learning operations. This lack of consistency in operation generates a source of confusion for the user and is best to be avoided when possible. · Typically, there are up to 24 buttons that can be learned.
To change Volume Lock back to the TV mode:
1. On the (C)A-LRC1, press and hold SETUP until the LED blinks twice, then release SETUP. Now, whenever you press VOL +, VOL , or MUTE on the (C)A-LRC1, volume will be controlled by your TV.
RE-ASSIGNING DEVICE KEYS
The (C)A-LRC1 can be set up to control a second TV or VCR, or any combination of eight home entertainment components. For example, to have the (C)A-LRC1 control a TV, a Cable Converter, and two VCRs, you will need to re-assign the key to operate the second VCR as follows: 1. On the (C)A-LRC1, press and hold SETUP until the LED blinks twice, then release SETUP. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components:
1. Turn on a component (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). We recommend highlighting or writing down the codes and device you wish to program before moving onto step 2. On the (C)A-LRC1, press a component key once (i. e. , CBL, VCR, TV, , , , or ). =VCR, DVD, LDP, Audio Cassette, DVR =TV =Satellite, DSS, Cable, Vid Acc. =CD, Home Automation, MD, Amp, Tuner, Misc. Audio =Amp, Tuner, Misc Audio, Home Automation, MD =Tuner, Amp, Misc, Audio, CD, Home Automation, MD 3. Use the Manufacturer's Codes (on the back side) to locate the the type of component and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again.
USER GUIDE INTRODUCTION
The (C)A-LRC1 from Russound is the complete solution for all of your remote control requirements. The (C)A-LRC1 is also customizable to allow for key configurations that meet your specific needs. It's also packed with these features for you to choose from: · Preprogrammed technology for easy setup · Designed for use with up to seven devices · Inclusive audio/video library · Dedicated operation of audio system keypad This manual provides a basic overview on how to set up and operate the (C)ALRC1. Please read the following instructions to see how easy setup is.
®
4. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. [. . . ] If you've located a setup code that works, but it has a separate TV code, you'll also need to program it into the (C)A-LRC1 to access volume control as follows: a. If there is no separate TV code listed, you will need to perform the following steps to access volume control: a. The LED will blink twice.
To Re-Assign Key:
Example: TV as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - TV When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the (C)A-LRC1 to control the new component (see Programming Component Control).
To Change A Reassigned Key Back:
Example: TV back to TV: SETUP - 9 - 9 - 2 - TV - TV
a. [. . . ]