User manual RUSSOUND CA4.4PI
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND CA4.4PI. We hope that this RUSSOUND CA4.4PI user guide will be useful to you.
Manual abstract: user guide RUSSOUND CA4.4PI
Detailed instructions for use are in the User's Guide.
[. . . ] A/V
DISTRIBUTION
&
CONTROL
SYSTEMS
Instruction Manual
4-Zone, 4-Source Central Controller/Amplifier
TUNER CD TAPE AUX
S O U R C E
CA4. 4pi
VOLUME
· ON / OFF · VOLUME · SOURCE
SOURCE
STORE
SOURCE REMOTE SENSOR
POWER
REMOTE SENSOR
4
ZONE
--
4
SOURCE
CENTRAL
CONTROLLER / AMPLIFIER
ON 1 2 3 4
OFF
POWER
ZONE CA 4. 4pi
1. Safety Instructions
"WARNING" " TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " "CAUTION" " TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] The tip is (+) and the sleeve is (-).
4
AC
DIM-1 Doorbell Interface
POWER DOORBELL INTERFACE TRANS DB3 DB2 DB1
TRIG
To Trigger Input on CA4. 4pi
TRIG OUT
+12V DC
To Doorbell
CD PLAYER
7. 6 Connecting The Infrared Components · In order for your CA4. 4pi to transmit the IR signal from the keypads to a source, an emitter must be connected from the IR outputs marked 1-4. Each of these outputs is wired in series and must be connected in consecutive order. For example, the #1 emitter output must be connected in order for the #2 emitter output to transmit the IR command. REAR OF · Connect each 845. 1 mini-emitter to the source IR output. · Remove the adhesive back and position the IR receiver on the product you wish to control. Stick the 845. 1 emitter directly over the source components IR window. The CA4. 4pi will direct the IR command to the source component you wish to control. · Repeat connections until all emitters match the selected sources.
845 EMITTER
CASSETTE DECK
845 EMITTER
TUNER
845 EMITTER
TO OTHER SOURCE
845 EMITTER
7. 7 Connecting the IR Link · When two CA4. 4pi Controllers are to be used in an installation, the IR Link connection is used to pass IR signal between the two units. Use a 1/8", mono, phone plug, male-to-male cable connected from the IR Link on the first CA4. 4pi Controller to the IR Link on the second CA4. 4pi. When connected, you may connect your IR emitters to either unit's IR Remote Output jacks. 7. 8 Keypad Connections · Each keypad connection on the back panel corresponds to the room / zone number chosen for your speakers. Each zone operates independently, so it is very important to connect the keypad to the correct zone keypad input. Remove the connector and strip 1/8" off each end of the wire insulation. At this point it is not important what color wires connect where, however, take note of the color of each wire and number indicated on the connector when connected to the back panel. Note: the keypad and the speakers in each room must be hooked to the same zone number. See List 3.
PRESET VOLUME LEVEL ADJUSTMENT
List 4 Room names should be written below. Zone 1 _______________ Zone 2 ______________ Zone 3 _______________ Zone 4 ______________ List 5 Wire color should be written below. Pin 1 ________ Pin 2 ________ Pin 3 _________ Pin 4 _________ Pin 5 ________ Pin 6 ________ Pin 7 _________ Pin 8 _________ NOTE: Preset volume and balance level adjustments can be made via the volume (VOL) and balance (BAL) potentiometers mounted on the keypad's circuit board.
8. Standard Keypad Installation The CA4. 4pi Central Controller Amplifier is offered with standard keypads and BALANCE LEVEL LCD keypads. ADJUSTMENT 8. 1 Installing the KP Keypads · The best performance is achieved with the keypad away from any direct sunlight. · Choose a place that is easily seen from the position where a person is most likely to be located. · Check whether or not you can route the wire to the location you have chosen. [. . . ] Immediately press the UP/ DOWN volume buttons to select the different source names. 4) Volume Up/Down: The UP/ DOWN arrows for volume are used to select the volume level and to select a different source name after the store button is pressed. 5) Power: Turn on or off any zone by pressing the power button on the front of the corresponding keypad. When the keypad comes on, it will automatically select the source that was previously selected and set the volume to minimum. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND CA4.4PI
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND CA4.4PI will begin.