User manual RUSSOUND CAM66X

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND CAM66X. We hope that this RUSSOUND CAM66X user guide will be useful to you.


RUSSOUND CAM66X : Download the complete user guide (8944 Ko)

Manual abstract: user guide RUSSOUND CAM66X

Detailed instructions for use are in the User's Guide.

[. . . ] CAM6. 6X-S1/S2 System 6-Zone, 6-Source XM Receiver and UNO Smart Keypads INSTRUCTION MANUAL IMPORTANT SAFEGUARDS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] Remove the adhesive back at the other end of the emitter and attach the emitter over the source component's IR window. In order to control this source component with IR, the source must be selected at the keypad receiving the command. CAM6. 6 with Optional Internal Source - XM satellite radio ANTENNA CAM6. 6 Use the source 1 output/input switch for audio out of the optional internal source or audio in of connected source equipment. CD Changer Tape Player 37 INSTALLER MAKING CONNECTIONS Common IR Connection Common IR Connections The Common IR jack on the rear of the CAM6. 6 allows control of any source equipment without that source being selected on the keypad. The connection for the COM IR jack is made using an IR emitter with a 1/8'' plug. The Russound 845. 1 single IR emitter is recommended, or use an IR connecting block such as the Russound 857 which allows multiple units to be controlled through the COM IR Port. ANTENNA CAM6. 6 Alternate configuration using 857 IR connecting block +12VDC STATUS 857 INFRARED CONNECTING BLOCK 1 +12VDC IR RECEIVER IN POWER IR emitters to source equipment 2 IR CONFIRM 3 EMITTERS IR COMMON IN +12VDC 4 5 GND STATUS 6 SIGNAL DESIGNED IN USA MADE IN KOREA 38 INSTALLER MAKING CONNECTIONS Speaker Connections The speakers are connected to the CAM6. 6 using modular snap connectors. Each of these color-coded connectors is designated for the speaker set of a particular amplified zone. To avoid confusion, connect one zone speaker set at a time starting with Zone 1, taking care to keep zone and speaker wire identities straight. Pull the speaker wire conductors apart so they're separated for the first two inches from their ends. Using a wire stripper, remove 1/4 inch of insulation from each conductor. The color code is as follows: WHITE -- L+ (left channel positive) GREEN -- L- (left channel negative) BLACK -- R- (right channel negative) RED -- R+ (right channel positive) Lift the black lever for each connection until it locks open and insert the proper speaker wire, matching channel and polarity for all four wires. Insert the modular connector into its designated output on the back of the CAM6. 6. Label each set of speaker wires with the zone and location. ANTENNA CAM6. 6 39 INSTALLER MAKING CONNECTIONS Zone Fixed/Variable Audio Outputs The CAM6. 6 has two Zone Audio outputs, on Zone 1 and Zone 2. Each of these zone audio output connections features a stereo line out RCA connection plus a switch to allow for either a fixed or a variable line level output. In the Fixed position, keypad volume level will not change the output level. The fixed or variable audio outputs can be used if additional amplification is desired (e. g. , Russound R235LS two-channel amplifier). Use quality RCA signal cables to ensure a constant quality audio signal. ANTENNA CAM6. 6 40 INSTALLER MAKING CONNECTIONS 12VDC Home Theater Trigger In/Out 12VDC Home Theater Trigger In This 12VDC Trigger input is used to control Power Management of the audio sources possibly being shared with a home theater system. When the last zone on the CAM6. 6 is turned off, 12VDC presence to the trigger input will prevent the sources that are on from being turned off. The connections for the trigger are made using a twoconductor cable with 1/8" male mini-plug. 12VDC 100mA Trigger Out The 12VDC 100mA trigger out can be used to engage any 12VDC trigger device or component such as the Russound ACT-1 triggered outlet. The connections for the trigger out are made using a two-conductor cable with 1/8" male mini-plug jacks at each end. The tip is positive (+) and sleeve is negative (-). ANTENNA CAM6. 6 41 INSTALLER MAKING CONNECTIONS 12VDC Mute Trigger In/Out 12VDC Mute Trigger In When 12VDC is applied to the Mute Trigger In, the system will fully mute any source connected to the Source Audio Input. The connections for the trigger are made using a two-conductor cable with 1/8" male mini-plug jacks. The CAM6. 6 can be programmed to mute audio for one or all zones as preferred when the 12VDC is applied. [. . . ] Audio from the source tuner can be split if used for all controllers. CAM6. 6X Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = All Controllers Output/Input Switch = Internal Source Output RCA cable connected to Source 1 CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner; Command Type = Peripheral Output/Input Switch = Input RCA cable connected to Source 1 Blues Blues Bluesville UNO-S1 UNO-S2 ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) RCA Cables Blues Blues Blues UNO-S1 UNO-S1 CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 107 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH TWO TUNERS System with two CAM6. 6X (internal tuner) controllers The configuration below is suitable for 7-12 zones that will have access to the tuner in the controller to which its keypad is connected only. If you have more than one internal tuner, you must set each tuner to its specific Controller ID number. If you want each controller to have access to dual tuners, a suggested solution is to use an ST2 Dual Tuner with two CAM6. 6s as shown on the next page. CAM6. 6X (1) Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = 1 CAM6. 6X (2) Controller Setup Menu: Controller ID = 2 Peripheral Setup Menu: Controller ID = 2 A CAT-5 patch cable is use to connect the RNET Link Out of Controller 1 to the RNET Link In of Controller 2. Sunny Sunny Sunny UNO-S1 UNO-S2 ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) CNBC CNBC CNBC UNO-S1 UNO-S2 ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 108 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH THREE TUNERS Sharing an ST2 Dual Tuner with multiple CAM6. 6 controllers (with and without tuners) The configuration below is suitable for 7 to 12 zones that can access the ST2 Dual Tuner and the CAM6. 6X tuner. This configuration uses RCA "Y" cables from the ST2 Tuner source outputs to connect to both CAM6. 6 source inputs. CAM6. 6X Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = All Controllers Source Setup Menu: Basic Setup Procedure: Source # = 2; Source Name = XM; Command Type = Peripheral Source # = 3; Source Name = AM/FM; Command Type = Peripheral Output/Input Switch = Internal Source Output RCA cable connected from Source 1 audio output on CAM6. 6X (1) to Source 1 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 1 audio output to Source 2 input on CAM6. 6X (1) RCA cable connected from ST2 Tuner 2 audio output to Source 3 input on CAM6. 6X (1) CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner; Command Type = Peripheral Source # = 2; Source Name = XM; Command Type = Peripheral Source # = 3; Source Name = AM/FM; Command Type = Peripheral Output/Input Switch = Input RCA cable connected from Source 1 audio output on CAM6. 6X (1) to Source 1 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 1 audio output to Source 2 input on CAM6. 6 (2) RCA cable connected from ST2 Tuner 2 audio output to Source 3 input on CAM6. 6 (2) ST2-XM Tuner Back Panel NEWMARKET, NH U. S. A. ST2 Smart Tuner INTERFACE LINK RS-232 KEYPAD PORTS FM COAX LOOP ANTENNA IR TUNER 2 AUDIO OUTPUT L R ANTENNA IR TUNER 1 AUDIO OUTPUT L R Serial# 12VDC 1. 5A MADE IN KOREA IN OUT RCA "Y" Cable UNO-S1 102. 5 102. 5 RCA Cable RCA Cable ANTENNA CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) UNO-S1 CNBC UNO-S2 CNBC CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 109 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH ST2 DUAL TUNER Sharing an ST2 Dual Tuner with multiple CAM6. 6 controllers (no built-in tuners) This configuration is suitable for 7 to 12 zones that can all access the ST2 Dual Tuner. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND CAM66X




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND CAM66X will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.