User manual RUSSOUND ISH1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND ISH1. We hope that this RUSSOUND ISH1 user guide will be useful to you.


RUSSOUND ISH1 : Download the complete user guide (977 Ko)

Manual abstract: user guide RUSSOUND ISH1

Detailed instructions for use are in the User's Guide.

[. . . ] Also, do not handle the product when your hands are wet or damp. Avoid heat. Locate the product away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Use the right power. Don't connect the product directly to electrical line voltage. [. . . ] If you have to run the cables parallel to electrical wiring, space the cables at least two feet (0. 6 m) from the AC power lines. The hub has 8-pole modular jacks for keypad and door station connections. These connections must be made according to the T568A standard as shown in the diagram below. Use a short 8-pole, 4-twisted-pair straight-through RJ-45 patch cable to link hubs together. RJ-45 Using T568A Wiring Standard INSTALLATION ISK2 ISH1 ISPS ISK3 ISK3 ISDR1 Six-zone ComPoint system with Advanced Keypads and an optional Door Strike Release Module 5 INSTALLATION Programming All system programming resides in the ISH1 Hub. For a six-zone system with ISK1 Basic Keypads, programming consists only of setting the doorbell chimes. For a system with ISK2 Advanced Keypads, programming includes assigning zone and door station labels. For a system with more than six zones, programming includes setting hub ID numbers. When multiple hubs are used, the zone and door label settings are initially stored in the hub to which the keypad is connected. Upon exiting the programming procedure, the settings are copied to the other hubs. Hub 1 serves as the master hub for storing all zone and door label settings. Whenever the system power is cycled, the settings are copied from hub 1 to the other hubs. Hub ID numbers In a system with multiple ISH1 Hubs, each hub must have a unique ID number. This is manually assigned on the 4-switch HUB ID DIP before the system is powered up. To assign the ID number, set switches 1 through 3 as shown in table 1. Leave this switch in the up position for system operation. 6 Hub ID Switch Settings (0 = Down, 1 = Up) Switches Hub 1 Hub 2 Hub 3 Hub 4 Hub 5 Hub 6 Hub ID 1 0 0 0 0 1 1 2 0 0 1 1 0 0 3 0 1 0 1 0 1 FW* 4 1 1 1 1 1 1 *Switch 4 is for firmware updates (0 = Update Mode, 1 = User Mode) Table 1. Hub ID switch settings Doorbell chimes A single 8-switch DIP assigns doorbell chimes for both door stations. Switches 1 through 3 select the chime for door 1 and switches 5 through 7 select the chime for door 2. There are 7 chime options, with a setting for no chime when a separate doorbell system is used. [. . . ] Damage to or destruction of components due to excessive power voids the warranty. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND ISH1




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND ISH1 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.