User manual RUSSOUND SDB 1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND SDB 1. We hope that this RUSSOUND SDB 1 user guide will be useful to you.


RUSSOUND SDB 1 : Download the complete user guide (2808 Ko)

Manual abstract: user guide RUSSOUND SDB 1

Detailed instructions for use are in the User's Guide.

[. . . ] For example, you can choose to listen to jazz music in a couple of rooms and classical music in all the others. Each room has its own input selector, volume control and on/off switch, located on the front of the unit. The SDB speaker selectors work with all speakers rated from 4 to 8 ohms, and amplifiers rated for 4 to 8 ohm loads. 2. [. . . ] The amplifier's minimum impedance is usually found following Wattage and Frequency Response in the amplifier's specification page of its manual. It may also be listed on the back panel of the amplifier near the speaker terminals. Identify the correct impedance-matching chart below according to your amplifier's minimum impedance: either for a 4 ohm amplifier or an 8 ohm amplifier. Determine the impedance for each pair of speakers by referring to its manual. Follow the appropriate row and column to determine jumper settings. Impedance Matching For 4 Ohm Amplifiers 8 Ohm Pairs 0 1 2 3 4 5 6 7 8 0 1X 2X 4X 4X 8X 8X 8X 8X 1 1X 2X 4X 4X 8X 8X 8X 8X 2 1X 2X 4X 4X 8X 8X 8X 8X 3 2X 4X 4X 8X 8X 8X 8X 4 2X 4X 4X 8X 8X 8X 8X 5 4X 4X 8X 8X 8X 8X 6 4X 4X 8X 8X 8X 8X 7 4X 8X 8X 8X 8X 8 4X 8X 8X 8X 8X 4. Setting System Volume It is important to properly adjust an impedance-matching system to avoid distortion or DC clipping (DC voltage will be produced from an amplifier that is overworked or that has an improper load). These can cause an amplifier/receiver to go into protection, and can cause autoformers on volume controls to heat up, damaging system components. To set up the system, the amplifier/receiver volume should be at its lowest setting, and the selector volume control should be at the highest setting. Slowly adjust the amplifier/receiver volume to a level that is acceptable for the amplifier to produce without clipping. 5. Operation To operate the SDB speaker selector, simply turn on the amplifiers and select a source for each amplifier. At the speaker selector, turn on the selected pair of speakers and select AMP A or AMP B. Set the volume by rotating the control clockwise to increase volume or counter-clockwise to decrease volume. The SDB speaker selectors allows operation of any combination of speakers selected to either amplifier A or B. 2 4 Ohm Pairs 4 Ohm Pairs 9 8X 8X 8X 8X 10 8X 8X 8X 8X 11 8X 8X 8X 12 13 14 15 16 8X 8X 8X 8X 8X 8X 8X 8X 8X Impedance Matching For 8 Ohm Amplifiers 8 Ohm Pairs 0 1 2 3 4 0 2X 4X 8X 8X 1 1X 4X 8X 8X 2345678 2X 4X 4X 8X 8X 8X 8X 4X 8X 8X 8X 8X 8X 8X 8X 8X Speakers SDB-6. 1 NEWMARKET, NH USA SPEAKER 6 L+ L- R- R+ SPEAKER 5 L+ L- R- R+ SPEAKER 4 L+ L- R- R+ SPEAKER 3 L+ L- R- R+ SPEAKER 2 L+ L- R- R+ SPEAKER 1 L+ L- R- R+ AMP B L+ L- R- R+ AMP A L+ L- R- R+ DESIGNED IN USA MADE IN CHINA SDB-6. 1 (back) Modular Snap Connector Wiring Order Modular Snap Connector (detail) LFP-1 (Optional) Use only with amplifiers whose frequency range extends BELOW 20Hz ON 1 B ON B VOLUME 2 ON / OFF ON B AMP/ RECEIVER B 2 OFF A AMP/ RECEIVER A SDB Series Speaker Selector Front Detail of dual-source speaker control Amplifier Connection Diagram for Russound SDB Series Dual-Source Speaker Selectors (Not to scale) INPUT L+ L- R- R+ OUTPUT L+ L- R- R+ WHITE -- L+ (left channel positive) GREEN -- L- (left channel negative) BLACK -- R- (right channel negative) RED -- R+ (right channel positive) RUSSOUND LFP-1 3 6. Specifications SDB-2. 1 Power : 100 watts per channel RMS continuous 200 watts per channel average 300 watts per channel peak 42 dB attenuation, 12 positions Russound Ultra-MatchTM Autoformers up to 14 gauge wire 8. 5" W x 3. 0" H x 6. 25" D (21. 6 x 7. 6 x 15. 9 cm) 4 lb (1. 8 kg) SDB-4. 1 Power : 200 W per channel RMS continuous 400 W per channel average 600 W per channel peak 42 dB attenuation, 12 positions Russound Ultra-MatchTM Autoformers up to 14 gauge wire 17. 0" W x 3. 0" H x 6. 25" D (43. 2 x 7. 6 x 15. 9 cm) 9 lb (4. 05 kg) Volume Control: Impedance Matching: Wire Size: Dimensions: Weight: SDB-6. 1 Power : Volume Control: Impedance Matching: Wire Size: Dimensions: Weight: Volume Control: Impedance Matching: Wire Size: Dimensions: Weight: 150 W per channel RMS continuous 300 W per channel average 450 W per channel peak 42 dB attenuation, 12 positions Russound Ultra-MatchTM Autoformers up to 14 gauge wire 17. 0" W x 3. 0" H x 6. 25" D (43. 2 x 7. 6 x 15. 9 cm) 10 lb (4. 5 kg) 7. Warranty The Russound SDB Series is fully guaranteed for Ten (10) years from the date of purchase against all defects in materials and workmanship. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. [. . . ] Russound sells product only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product. 5 Forbes Rd. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND SDB 1




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND SDB 1 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.