User manual RUSSOUND ST2 REV 2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND ST2 REV 2. We hope that this RUSSOUND ST2 REV 2 user guide will be useful to you.
Manual abstract: user guide RUSSOUND ST2 REV 2
Detailed instructions for use are in the User's Guide.
[. . . ] ST2 Smart Tuner
Dual AM/FM Tuner INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. [. . . ] In addition to direct selection, the memory presets can be accessed by using and scroll through all presets for the bank selected. to
Selecting the desired band
Push to switch between AM and FM reception.
Selecting the desired frequency
Press and release and for manual tuning.
Selecting Stereo or Mono Output
Press and release to toggle between stereo and mono mode. STEREO or MONO appears briefly on the screen when selecting mode.
Backup and Restore
Once all of the tuner settings are completed, it may be advisable to create a backup of the programmed settings for future use. The backup will then be available in case tuner settings need to be restored. The "RNET Backup Utility" is available through the Document Center at www. russound. com. Also required are a DB9 male-to-female cable and laptop or desktop PC.
Selecting Distant or Local Reception
Press and hold to toggle between distant and local mode. In cities, antennas can pick up multipath signals when they bounce off buildings and get doubled. The Local mode limits the noise associated with these reflected signals.
Bank/Memory Presets
Each tuner has six banks of preset memory settings, and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets). Presets are associated with the tuner that is selected at the time the preset is saved.
14
ST2 OPERATION
ST2-RC REMOTE CONTROL
ST2-RC Remote Control Operation
Turning the unit on
To take the ST2 tuner out of standby mode, push or any other button except TUNER 1 or TUNER 2.
PWR
Selecting Stereo or Mono Output
Press to toggle between stereo and mono mode. On a preset, the stereo/mono setting is saved for that preset.
ST/ MONO
Selecting the desired tuner
(Note: To change the tuner that is audio-active, you must have some other system control in place to change the source) To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner.
TUNER 1 TUNER 2
Selecting Distant or Local Reception
Press to toggle between Distant and Local mode. Normal operation is in Distant mode.
LOC/ DX
Recalling a Memory Preset
To recall a memory preset, select the desired tuner, press
MEM BANK
to select the desired bank, then press
Selecting the desired band
Push
AM/FM
and enter the desired preset number (1 to 6). The memory presets can also be accessed by using
MEM
to switch between AM and FM reception.
and to scroll through all presets for the selected bank.
MEM
Selecting the desired frequency
TUNE
Saving Favorites
The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding
FAV 2
FAV 1
Use and for manual tuning. To move quickly through the stations, press and hold either of the Tune buttons for more than 1. 5 seconds.
TUNE
To directly select a station, press , and enter the three- or four-digit station frequency (1071 for 107. 1, etc. ). European regions use five-digit station frequencies.
TUNE
or
until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either
FAV 1
or
FAV 2
.
Frequency Seek
The SEEK function is performed by pressing and releasing to seek lower frequencies or for higher frequencies. SEEK tuning begins at the current frequency, seeks upward and stops at the next tuned station. Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency.
15
ST2 OPERATION
ST2-KP KEYPAD CONTROLS
ST2-KP Keypad Operation
1
5
ST2-KP Keypad Display
Turning the keypad on/off
To activate the ST2-KP, press . The keypad remains powered until the ST2 Tuner is turned off.
1
The 5-character backlit display shows frequency and band, plus presets. Messages scroll twice, then display the first 5 characters.
Selecting the desired tuner
To select a different tuner, press and hold . [. . . ] Use + and - buttons to select the source number to which Tuner 1 is connected. Use + and - buttons to select the name for the source (e. g. , Tuner 1). Press the Setup button three times to back out of the Installation Menu. Source Configuration Note: When the ST2 Tuner is used with the CAV6. 6 or other RNET controller, it is configured as an RNET command type "Peripheral" and is connected via the RNET bus. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND ST2 REV 2
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND ST2 REV 2 will begin.