User manual RUSSOUND ST2-XM 1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND ST2-XM 1. We hope that this RUSSOUND ST2-XM 1 user guide will be useful to you.
Manual abstract: user guide RUSSOUND ST2-XM 1
Detailed instructions for use are in the User's Guide.
[. . . ] 800. 967. 2346
IMPORTANT SAFEGUARDS
11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. [. . . ] In addition, the LCD panel is also backlit green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset, and all subsequent memory preset entries will be associated with that selected tuner.
Bank/Memory Presets
Each tuner has six banks of preset memory settings, and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets). Presets are associated with the tuner that is selected at the time the preset is saved.
Memory Preset programming
From the front panel, perform these steps: 1. Use .
Selecting the desired band (AM/FM only)
Push to switch between AM and FM reception.
to choose from one of six banks (1-6). Tune to the desired station or channel.
Selecting a mode (XM)
Push to select an XM operating mode.
Exiting a mode (XM)
Push to exit the XM mode selection menu.
Signal Strength mode (XM)
Press and hold and release. Push the desired memory preset (M1 through M6) button for more than 2 seconds. When the memory preset is saved, the appropriate preset number (M1 through M6) and SAVED appears on the LCD. The selected station setting reappears and the sound resumes after the button is released.
Recalling a Memory Preset
To recall a memory preset, use to select the desired bank, then press the desired preset button (M1 to M6). In addition to direct selection, the memory presets can be accessed by using and scroll through all presets for the bank selected. To exit press
Selecting the desired frequency or channel
Press and release and for manual tuning.
Selecting Stereo or Mono Output (AM/FM only)
Press and release to toggle between stereo and mono mode. STEREO or MONO appears briefly on the screen when selecting mode.
Backup and Restore
Once all of the tuner settings are completed, it may be advisable to create a backup of the programmed settings for future use. The backup will then be available in case tuner settings need to be restored. The "RNET Backup Utility" is available through the Document Center at www. russound. com. Also required are a DB9 male-to-female cable and laptop or desktop PC.
Selecting Distant or Local Reception (AM/FM only)
Press and hold to toggle between distant and local mode. DISTANT or LOCAL appears briefly on the
19
ST2-XM OPERATION
ST2-RC REMOTE CONTROL
ST2-RC Remote Control Operation
The ST2-RC remote control is the only means of remote operation of the ST2-XM in a non--RNET system. The ST2-XM front panel displays information for the tuner that is receiving commands from the ST2RC. However, the ST2-RC commands do not change which tuner is playing; that is done through the system's source selection.
Frequency Seek (AM/FM only)
The SEEK function is performed by pressing and releasing to seek lower frequencies or for higher frequencies. SEEK tuning begins at the current frequency, seeks upward and stops at the next tuned station. Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency.
Turning the unit on/off
To switch the ST2 tuner in or out of standby mode, push TUNER 2.
PWR
Selecting Stereo or Mono Output (AM/FM only)
Press to toggle between stereo and mono mode. On a preset, the stereo/mono setting is saved for that preset.
ST/ MONO
or any other button except TUNER 1 or
Selecting the desired tuner
To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 (XM) and amber for Tuner 2 (AM/FM). Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner.
TUNER 1 TUNER 2
Selecting Distant or Local Reception (AM/FM only)
Press to toggle between Distant and Local mode. [. . . ] Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note: When the ST2-XM Tuner is used with the CAV6. 6 or other RNET controller, it is configured as an RNET command type "Peripheral" and is connected via the RNET bus. This makes the tuner behave as a fully integrated device with UNO keypad support. Each tuner must be set up with a unique source number (1 - 6) or unassigned. Key Function Note: When using the tuner with an RNET system, do not reassign keypad and remote buttons for tuner control in the controller's Key Configuration Menu. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND ST2-XM 1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND ST2-XM 1 will begin.