User manual RUSSOUND UNO-LRC1

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND UNO-LRC1. We hope that this RUSSOUND UNO-LRC1 user guide will be useful to you.


RUSSOUND UNO-LRC1 : Download the complete user guide (229 Ko)

Manual abstract: user guide RUSSOUND UNO-LRC1

Detailed instructions for use are in the User's Guide.

[. . . ] On the UNO-LRC1, press DVD Press and hold SETUP until the LED blinks twice, then release SETUP. Use the Setup Codes For TV/VCR Combos (on the back side) to locate the brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the remote control at the the TV and slowly alternate between pressing PWR and TV. [. . . ] For Sharp, use TV code 0093 and VCR code 0048. PROGRAMMING COMPONENT CONTROL The UNO-LRC1 can control up to eight different components. Perform the following instructions for each component you want controlled: NOTE: For TV/VCR Combo control, see the next section. LEARNING CAPABILITY To optimize success, the learning process should be conducted in an area where there is a low level of IR emission. High levels of "natural light" or energy efficient fluorescent lights could interfere with a learning event The source and target (learner) remotes should be no more than 1 to 2 inches apart during a learning event and the IR LEDs of the two units should be aligned with each other. Press [MODE] and key to be learned (time out if no key pressed in 10 seconds). Visible LED flashes rapidly (time out if no received signal detected in 4 sec. ) 4. Exit learning mode by pressing SETUP, or by time out (10 seconds). At step 5, one long blink indicates learning failure, which could be: · There are certain device codes which are not learnable. · The learner will support IR codes with carrier frequency up to 135 Khz. · All keys with the exception of Modes, and SETUP can be learned on. The source remote and target should be no more than 1 to 2 inches apart. · In some cases you may be required to re-learn a code if it is not correctly learned. · The learning process should conducted in an area where there is a low levels of IR emission. High levels of "nature light" or Energy efficient fluorescent lights, could interfere with a learning event. · In general, it is not recommended to learn a function to the Record Key. The Record Key requires a double key press to send the record function in normal operation. The double key press is lost when the Record key is involved in most learning operations. This lack of consistency in operation generates a source of confusion for the user and is best to be avoided when possible. · Typically, there are up to 24 buttons that can be learned. CHANGING VOLUME LOCK The UNO-LRC1 is set to control volume of a component through your TV while in the , , or mode. If your TV is not remote controllable, or if you want volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e. g. , through the cable in the TV mode). 1. Turn on a component (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). We recommend highlighting or writing down the codes and device you wish to program before moving onto step 2. [. . . ] On the UNO-LRC1, press and hold SETUP until the LED blinks twice, then release SETUP. Now, whenever you press VOL +, VOL ­, or MUTE on the UNO-LRC1, volume will be controlled by your TV. FEATURES AND FUNCTIONS Use the Key Charts to learn how the UNO-LRC1 functions. 4. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code). NOTE: If the device does not have a PWR key, press PLAY. a. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND UNO-LRC1




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND UNO-LRC1 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.